Short answer first: the refrigerant decides how environmentally friendly and how future-proof your air conditioner or heat pump is.
R290 (propane) is the most future-proof choice and is mainly found in monobloc heat pumps. R32 is still perfectly fine and sits in most split air conditioners and in plenty of heat pumps. R410A is outdated, has a high environmental impact and is being phased down. You should not be buying a new unit on R410A.
Below I explain what a refrigerant actually does, what GWP and those flammability classes mean, and which choice fits your situation. With a comparison table and concrete buying advice.
What is a refrigerant, exactly?
A refrigerant is the substance that circulates through the sealed circuit of your air conditioner or heat pump.
It evaporates and condenses over and over again. That is how it pumps heat from one side to the other: in summer your air conditioner takes heat out of the house, and in winter your heat pump takes heat out of the outside air and brings it indoors.
Without refrigerant the unit does nothing. So it is not a “fuel” that gets used up. It is a substance that goes round and round inside a sealed system, year after year.
Why should you care which type is in there? Two reasons:
1. Environmental impact if it leaks. As long as the system is sealed, nothing happens. But if a leak ever develops, the refrigerant escapes into the air. Some refrigerants are powerful greenhouse gases at that point, others are almost harmless.
2. How future-proof your unit is. Europe and the UK are phasing down refrigerants with a big climate impact. Choose a unit with an outdated refrigerant today and servicing it later can get more expensive and more awkward.
What does GWP mean?
GWP stands for Global Warming Potential.
It is a number that tells you how much a substance contributes to global warming compared with CO2. CO2 is the yardstick and gets a GWP of 1.
A simple example: a refrigerant with a GWP of 675 is, kilo for kilo, as damaging to the climate when it leaks as 675 kilos of CO2. A refrigerant with a GWP of 3 is roughly as damaging per kilo as 3 kilos of CO2. That difference is enormous.
The lower the GWP, the better for the environment if a leak ever happens. And the smaller the chance that the refrigerant gets phased out by regulation.
The GWP values you see in this article are the common reference figures used in the trade and in the regulations. They can differ slightly from source to source, because several scientific reference tables exist.
The F-Gas Regulation in plain English
F-gases are “fluorinated greenhouse gases”. They are a group of synthetic substances that used to be the standard choice for refrigerants. R410A and R32 belong to this group.
The GB F-Gas Regulation (the retained version of EU Regulation 517/2014) squeezes the availability of high-GWP F-gases step by step. That is called a “phase-down”. Northern Ireland follows the EU rules, which were tightened further under EU Regulation 2024/573.
In broad strokes it comes down to this:
- Less and less of these substances comes onto the market, through a declining quota.
- Gradually stricter GWP limits apply to new equipment, which pushes manufacturers towards lower-GWP refrigerants.
- Natural refrigerants such as propane (R290) and CO2 (R744) fall outside that squeeze and stay available without limit.
For the exact dates and threshold values I deliberately point you to the official source, because they differ per product category (split, monobloc, capacity) and change over time. Check gov.uk or the Environment Agency for the current position.
Important: a system you already have in your home is fine to keep and fine to have serviced. The phase-down is about newly placed equipment, not about your existing heat pump or air conditioner.
Flammability classes: A1, A2L and A3
Refrigerants are given a safety class. For flammability there are three labels you will run into again and again:
A1 (non-flammable). Does not burn. R410A falls in this group. Sounds safe, but these refrigerants often have a high GWP.
A2L (mildly flammable). Burns only with great difficulty and only under specific conditions. R32 falls in this group. This class is the practical middle ground: a much lower GWP than the A1 refrigerants, and safe enough for split systems with an indoor unit, provided it is installed to the rules.
A3 (flammable). Burns readily, just like the gas in your hob or your camping gas bottle. R290 (propane) falls in this group.
That flammability sounds dramatic, but in practice it is not a big deal. What it does determine is where and how the unit is allowed to be installed.
With an A3 refrigerant like propane, you do not want the refrigerant inside the house. That is why R290 is almost always used in a monobloc heat pump: a single cabinet that stands outside with the complete refrigerant circuit inside it. Indoors, only ordinary central heating water runs through your pipes. So the propane never enters your home.
With an A2L refrigerant like R32, the refrigerant is allowed to run through pipework to an indoor unit, as in a split air conditioner or a split heat pump. In that case there are requirements for the refrigerant charge and the size of the room, to keep things safe.
Refrigerant comparison table
| Refrigerant | GWP (approx.) | Type | Safety class | Typical application | Points to watch |
|---|---|---|---|---|---|
| R410A | ~2,088 | Synthetic (HFC) | A1, non-flammable | Older split air conditioners and heat pumps | High GWP, being phased out. Topping up is getting expensive and scarce. Do not buy new. |
| R32 | ~675 | Synthetic (HFC) | A2L, mildly flammable | Current standard in many split air conditioners and heat pumps | Far lower GWP than R410A. Still widely available, but also falls under the phase-down. |
| R290 (propane) | ~3 | Natural | A3, flammable | Monobloc heat pumps (whole circuit outdoors) | Very low GWP, future-proof. Built as a monobloc because of the flammability. |
| R454B | ~466 | Synthetic (blend) | A2L, mildly flammable | Transitional alternative to R410A in some air conditioners and heat pumps | Lower GWP than R32, but not a natural refrigerant. |
| R744 (CO2) | 1 | Natural | A1, non-flammable | Hot water heat pumps and domestic hot water (high temperature) | Runs at very high pressure. Ideal for hot water up to around 90 degrees. |
In short: the further down the table you go towards the natural refrigerants (R290, R744), the lower the climate impact and the more future-proof the choice.
What does this mean for buying now?
You do not need to become an engineer. These rules of thumb will get you to a good decision.
R290 monobloc: the future-proof choice
If you are choosing a heat pump today, a monobloc on R290 (propane) is the most future-proof option.
The GWP is minimal, the refrigerant falls outside the phase-down and the complete circuit sits safely outdoors in one cabinet. Plenty of manufacturers (Daikin, Vaillant, Bosch and Mitsubishi Electric among them) now have R290 models in their range.
Bonus: propane often performs slightly more efficiently at higher flow temperatures, which is handy in older, less well insulated houses.
R32: still perfectly fine
Does the unit you have your eye on contain R32? No need to panic.
R32 has a far lower GWP than the old R410A and is still widely available. For split air conditioners, R32 is simply the standard at the moment and a solid choice.
Worth knowing: R32 also falls under the gradual phase-down of F-gases. In the longer run the market keeps shifting towards natural refrigerants. For an air conditioner you will replace in 10 to 15 years anyway, that is usually not a problem.
R410A: better to avoid now
You should not buy a new unit on R410A.
The GWP is high, the refrigerant is being phased out and the price of topping it up keeps climbing because of scarcity. You will feel that in your wallet later, at service and repair time.
Already got a working R410A installation? Keep it and have it serviced as normal. But when it comes to replacement, move to a more modern refrigerant.
What it means for maintenance, servicing and topping up
The refrigerant choice affects more than the environment. It also affects your running costs over time.
Scarcity and price. High-GWP refrigerants such as R410A are getting scarcer because of the phase-down. The price per kilo goes up as a result. If an old system like that ever needs topping up after a leak, it can get seriously expensive.
Availability of servicing. As a refrigerant is phased out, engineers and wholesalers work with it less and less. For common refrigerants like R32 and R290 servicing is widely available. For heavily outdated refrigerants it gets difficult.
Topping up should not be needed. A properly installed, sealed system loses no refrigerant in principle. If it does need topping up, there is usually a leak that has to be repaired first. So topping up is not routine maintenance. It is a repair.
Can you top up refrigerant yourself?
No. And that is not a technicality.
Working with F-gases (such as R32 and R410A) legally requires F-Gas certification. Only a certified engineer is allowed to recover, top up or open the circuit. That rule exists to prevent leaks and unsafe situations.
With a monobloc on R290 there is nothing for you as a householder to do to the refrigerant circuit at all. It is factory filled and hermetically sealed. No refrigerant pipework enters your house, so there is nothing to top up and nothing to tinker with.
Using a DIY “air con recharge kit” off the internet on a fixed installation is therefore a bad idea: it is not allowed, and you risk damage and leaks.
Refrigerants and the Boiler Upgrade Scheme
Heat pumps may qualify for a grant under the Boiler Upgrade Scheme, administered by Ofgem, and installation generally has to be carried out by an MCS-certified installer.
Whether a unit qualifies depends broadly on the type of heat pump and its energy performance (such as the SCOP value). On top of that, policy is paying more and more attention to the environmental impact of the refrigerant, where a lower GWP is the favourable side to be on.
The exact conditions, amounts and any GWP thresholds change regularly. So always check the current eligibility rules and product listings on gov.uk and with MCS before you buy. A good installer will usually know exactly which models qualify at the time.
Practically speaking: if you were already going for an efficient heat pump with a low-GWP refrigerant such as R290, you are on the right side of where things are heading.
Which unit should you choose, and when?
Everything in one list, so you know straight away what suits you:
- New heat pump, and I want it to last me years? Go for a monobloc on R290. Lowest GWP, future-proof, safely installed outdoors.
- Split air conditioner for cooling (and a bit of heating)? R32 is the common, perfectly good choice. Look for solid energy efficiency.
- Mainly need a lot of hot water? Look at a hot water heat pump. Some use R744 (CO2), which is ideal for high hot water temperatures.
- Existing unit on R410A? Keep it and have it serviced for as long as it works well. Switch to a modern refrigerant when you replace it.
- Someone offering you a new unit on R410A? Don’t. Ask for R32 or R290 instead.
Frequently asked questions
Which refrigerant is best for a heat pump?
For most households a monobloc heat pump on R290 (propane) is the best choice: very low GWP, future-proof and safe, because the whole refrigerant circuit stands outside. R32 is a good and widely used alternative, especially in split versions.
Is R290 (propane) dangerous in my heat pump?
Propane is flammable (class A3), but in a monobloc heat pump it is completely sealed inside the outdoor unit. No propane comes into your house. Manufacturers also build in safety measures. Installed correctly, it is safe to use.
Can I still buy an air conditioner or heat pump with R410A?
A new unit on R410A is no longer a sensible purchase. The refrigerant has a high GWP and is being phased down, which makes topping up and servicing more expensive and harder in future. Go for R32 or R290 instead.
Can I top up my air conditioner or heat pump myself?
No. F-gases such as R32 and R410A legally require F-Gas certification, and only a certified engineer may work on them. A monobloc on R290 is factory filled and sealed, so there is nothing to top up.
Is R32 banned?
R32 is not banned, but it does fall under the gradual phase-down of higher-GWP F-gases. It is still widely available and a perfectly good choice, while the market slowly shifts towards natural refrigerants such as R290. Check gov.uk for the current rules.
How do I find out which refrigerant is in my unit?
It is on the data plate or the label on the outdoor unit, usually as an R-code such as R32 or R290. You will also find it in the manual and on your installer’s quotation. Not sure? Ask your installer before you buy.
Smart upgrading starts with the right choice
Choosing the right refrigerant is exactly the sort of decision that saves you money and hassle later on: a low-GWP unit is better for the climate and future-proof at the same time. Want to make your home smarter and cheaper to run step by step, from insulation to heat pump? Have a look at energie-verpulveraar.fredsbouwtekeningen.nl. There we help you with clear, no-nonsense explanations to smash your energy bill without having to become an engineer for it. Take the first step today.

