How to make a cat scratching post that is sturdy and tall

Facebook
Twitter
LinkedIn
Pinterest

You make a cat scratching post from a solid post (round timber of 8 to 10 cm in diameter), a heavy base board of at least 40×40 cm and no less than 3 cm thick, and 8 mm sisal rope that you wrap tightly around it with wood glue.

Allow 30 to 50 metres of sisal rope for a post of roughly 1 metre tall. The whole job costs you 25 to 70 euros in materials and half a day of work.

The big advantage: building it yourself gets you a post that will not tip over, that is tall enough for your cat to stretch out fully, and that you can simply re-wrap later instead of binning. You rarely get that from a 30 euro shop-bought post.

Below you will find exactly which dimensions to stick to, how much rope you need, how to fit the rope and which mistakes to skip.

Why build a scratching post yourself?

Three reasons, and they are connected.

Stability. Cheap shop-bought posts often have a thin, light base. The cat jumps on it, the post wobbles, and after one topple your cat will not touch it again. Build it yourself and you make the base as heavy as you like.

Height. A cat wants to stretch out fully while scratching, front paws well above its head. Plenty of ready-made posts are only 50 to 60 cm tall. For a grown cat that is simply too short.

Cost and lifespan. Making your own is not always cheaper than the very cheapest post out there, but you do get far more post for your money. And when the rope wears out after a few years, you wrap fresh rope around it instead of throwing the whole thing away.

What dimensions should a good scratching post have?

This is where most self-builders go wrong. Stick to these rules of thumb.

Part Recommended size Why
Height of scratching section At least 80 to 100 cm So a grown cat can stretch out fully
Height for large breeds 120 cm or more Maine Coons, Norwegian Forest Cats and the like are longer
Post thickness 8 to 10 cm in diameter Thin timber flexes and feels unstable
Base board At least 40×40 cm, ideally 50×50 cm A wide base does not tip
Base board thickness At least 3 cm Mass at the bottom keeps the post upright
Base board weight At least 4 to 5 kg Absorbs jumping and climbing

Rule of thumb for stability: the taller the post, the wider and heavier the base. At 120 cm or more you are heading towards a 50×50 cm base board, or you fix the post to the wall (more on that further down).

Take the height from your own cat. Let your cat reach up against a door frame and measure how high its front paws get. Add the scratching section measured from the base board and you have your minimum height.

What materials do you need?

You build a basic post with these materials.

  • Post: round timber of 8 to 10 cm in diameter. Think of a thick branch (chestnut is a popular choice), a wooden post from the DIY store or a length of hardwood. Length equal to your desired height plus a little extra for screwing it down.
  • Base board: plywood or MDF at least 3 cm thick and at least 40×40 cm. For extra weight you can glue two boards together.
  • Sisal rope: 8 mm is the happy medium. 6 mm is finer but wears out faster, 10 mm is coarser and stiffer to work with. Allow 30 to 50 metres per metre of post height.
  • Wood glue: white PVA wood glue (Evo-Stik, Gorilla and UHU all do one). It is water-based and safe for your cat once cured. Do not use solvent-based or contact adhesive.
  • Screws: long wood screws, ideally stainless steel, roughly 120 to 140 mm, to fix the post through the base board.
  • Optional: carpet or hard-wearing fabric to cover the base board and any platforms, plus a staple gun to fix that fabric down.

Tools: saw, drill or cordless screwdriver, wood bit, tape measure, pencil and a pair of scissors or a sharp knife for the rope.

Exactly how much sisal rope do you need?

The rough rule of thumb is 30 to 50 metres for a 1 metre post. But you can work it out precisely, and that saves you a half-empty reel or one that falls just short.

Here is the sum:

  1. Measure the circumference of your post. Circumference = diameter x 3.14. So an 8 cm post has a circumference of about 25 cm.
  2. Work out how many wraps will fit. With 8 mm rope you fit roughly 12 wraps per 10 cm of post height (each wrap is 0.8 cm tall). For 100 cm that is around 125 wraps.
  3. Multiply: 125 wraps x 0.25 metres circumference = roughly 31 metres of rope.

As a sanity check, the figures you come across online line up with this: for a post 60 cm tall and 8 cm thick you need about 14 metres of 8 mm sisal rope. Always buy a bit extra, because tightly wrapped rope shortens as it goes on.

Sisal rope needed by post heightPost 60 cm tallPost 60 cm tall: 14 m14 mPost 100 cm tallPost 100 cm tall: 31 m31 m
Rope required for an 8 mm sisal wrap on a post 8 cm in diameter.

Sisal or jute: what is the difference?

Both are natural fibres and both are safe for cats, but there are clear differences.

Sisal Jute
Wear resistance High, lasts a long time Lower, wears out faster
Fibre strength Stiff and strong Softer and finer
Loose fibres Few More, so more risk if chewed
Price Slightly dearer Cheapest

For the scratching section, go for sisal. It is tougher, lasts longer and leaves behind fewer loose fluffs for your cat to swallow. Jute is fine for looks or for spots that take little punishment, but not for the post itself.

Step by step: how to build the scratching post

Allow half a day, not counting the drying time of the glue.

Step 1: Cut the post to length. Saw it square to your desired height plus the thickness of the base board. Sand the sawn ends smooth.

Step 2: Prepare the base board. Cut the board to at least 40×40 cm. If you want more weight, glue two boards together. Find the centre by drawing corner to corner.

Step 3: Drill pilot holes. Drill from the underside of the base board through the centre, and drill a short pilot hole into the bottom of the post as well. Pilot holes stop the timber from splitting.

Step 4: Screw the post down. Fix the post with two or three long screws driven up through the base board. Tighten them firmly and check that the post stands plumb, using a spirit level if needed.

Step 5: Test the stability. Push the top of the post hard from side to side. Does it wobble, or does the board lift? Sort that out now, not once the rope is on. Extra screws or a heavier board will do it.

Step 6: Apply the glue. Spread a band of wood glue around the bottom of the post. Work in sections of 20 to 30 cm so the glue does not dry out before you get to it.

Step 7: Wrap the sisal rope. Start at the bottom. Twist the rope tight and push every wrap firmly against the one before it, leaving no gaps. Tightness matters more than speed. Work your way up and add more glue every few wraps.

Step 8: Secure the start and the end. Fix the end down with a staple or a small screw that you sink flush, so the cat cannot pull at it.

Step 9: Cover the base board (optional). Stretch carpet or hard-wearing fabric over the board and staple it on the underside.

Step 10: Let the glue cure fully. Wait at least 24 hours before your cat is allowed on it. Fresh glue is not something your cat should be licking.

How do you stop the post from tipping over?

Tipping over is the number one reason cats ignore a scratching post. Three ways to prevent it.

A heavier base. The simplest fix. A double base board, or a board of at least 50×50 cm for a tall post.

Fix it to the wall. For posts above 120 cm this is the safest option. Fix the top of the post to the wall with a small bracket or a batten. Then it simply cannot fall.

A cross under the board. Screw two battens in a cross underneath the base board. That widens the footprint without needing an enormous board.

Adding platforms and a house

If you want more than a bare post, extend it with platforms and a house.

Make a platform from a board of at least 30×30 cm, screwed down into the post from above. Cover it with carpet or fabric for grip and comfort.

A house is a closed box with an opening, often at the bottom or halfway up. Cats like an enclosed spot to hide away in. Watch the weight: the more you build on top, the heavier and wider the base needs to be, or the more important it becomes to fix the post to the wall.

Maintenance: replacing the rope

Sisal rope wears out. After a few years of heavy use it goes fluffy and thin at the bottom. Good news: you do not throw the post away.

Cut the old rope off, scrape away the glue residue and wrap fresh sisal rope on the same way. This is exactly why building your own pays for itself. The frame is already there.

What does a homemade scratching post cost?

A realistic range, depending on whether you have materials lying around or buy everything new.

Item Cost
Post (DIY store or free branch) 0 to 15 euros
Base board (plywood/MDF) 5 to 15 euros
Sisal rope (30 to 50 metres, 8 mm) 15 to 35 euros
Wood glue and screws 5 to 10 euros
Total 25 to 70 euros

The biggest item is the sisal rope. If you have reclaimed timber or a suitable branch, you land at the bottom of that range.

Common mistakes

  • Building the post too short. Below 80 cm a grown cat cannot stretch out. Measure against your own cat.
  • Too light a base. The number one reason posts tip over and get ignored. Better too heavy than too light.
  • Wrapping the rope too loosely. Loose rope turns with the cat as it scratches and breaks up quickly. Tight, wrap against wrap, no gaps.
  • The wrong glue. Use water-based wood glue, not solvent adhesive, and let it dry fully before use.
  • Not testing the post before the rope goes on. You can fix a wobble on a bare post, not once 40 metres of rope is wrapped around it.
  • Forgetting stability when you add platforms. Every platform and house makes the post top-heavy. Weigh the base down or fix it to the wall.

Frequently asked questions

How much sisal rope do I need for a scratching post?
Allow 30 to 50 metres for a post 1 metre tall and 8 cm thick. To work it out exactly, take the circumference (diameter x 3.14) times the number of wraps. For a post 60 cm tall and 8 cm thick that comes to roughly 14 metres of 8 mm rope.

Which thickness of sisal rope is best?
8 mm is the most common choice and a good middle ground. 6 mm is finer but wears out faster, 10 mm is coarser and stiffer to work with.

How tall should a scratching post be?
At least 80 to 100 cm for an average grown cat, so it can stretch out fully. For large breeds such as the Maine Coon, go for 120 cm or more.

Which glue is safe for cats?
White water-based wood glue (PVA). It is safe once fully cured. Let the post dry for at least 24 hours before your cat gets near it. Avoid solvent-based and contact adhesives.

Is sisal or jute better for a scratching post?
Sisal, for the scratching section. It is tougher, more hard-wearing and leaves behind fewer loose fibres than jute. Jute is cheaper but does not last as long.

How do I stop the scratching post from tipping over?
Use a heavy, wide base board (at least 40×40 cm and 3 cm thick) and fix tall posts above 120 cm to the wall with a small bracket.

Get going with a proper plan

A sturdy scratching post that will not tip over starts with the right dimensions and a well thought-out design. Would you rather not measure and guess your way through it, but start straight away with a fully worked-out plan? Then have a look at Fred’s plans at https://www.fredsdiyplans.com/. You will find clear plans there that get you building right the first time, with no surprises halfway through. Enjoy the build.

Related articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Categories

.

Fred’s DIY Plans