Building a larder cupboard: a free-standing pantry unit for your kitchen

Facebook
Twitter
LinkedIn
Pinterest

A larder cupboard is the one piece of furniture that makes your kitchen feel twice as calm overnight. All your food storage behind two doors, everything visible the moment you open them, and nothing left quietly going out of date at the back of a deep cupboard.

Straight to the point: you build a larder cupboard as a free-standing tall unit roughly 190 to 220 cm high, 60 to 120 cm wide and 40 to 60 cm deep, with adjustable shelves spanning no more than 60 to 80 cm in 18 mm board. You make the carcass from 18 mm plywood or furniture board, hang two doors on three or four cup hinges each, fit shallow racks (10 to 15 cm) to the inside of the doors, and you fix the cupboard to the wall every time so it cannot topple.

The secret to a good larder cupboard is not in the building. It is just a cupboard. It is in the depth and the layout. Make it too deep and you have an expensive version of the same jumble cupboard. Below I show you how to avoid that, with sizes, an example cutting list and the mistakes most people make.

What exactly is a larder cupboard?

The name comes from the traditional English kitchen. A larder was the cool store room where meat, dairy and dry goods were kept, often with a cold stone slab and a mesh grille for ventilation. The modern larder cupboard is the furniture version of that: a tall, free-standing unit with double doors that holds your dry stores, your breakfast things and sometimes a small worktop.

How it compares with the other options in your kitchen:

Type What it is Strength Weakness
Larder cupboard Free-standing tall unit with double doors, door racks and sometimes a worktop Everything at a glance, movable, a proper piece of furniture Takes floor space, needs wall space
Pull-out larder unit Narrow pull-out (30 to 60 cm) built into the kitchen run Reachable from both sides, fits a tight gap Limited capacity, expensive runners, weight limit
Built-in pantry unit Tall unit as part of the kitchen run Integrates neatly, plenty of volume Usually too deep, things vanish at the back
Separate pantry or utility room A room of its own with shelving Unlimited volume Only if you have the space
Open shelving Shelves on the wall Cheap, quick Dust, light, a cluttered look

What makes a larder cupboard special: you can take it with you when you move. It is furniture, not kitchen. For anyone renting, that is often exactly why they choose one.

The most important design rule: not too deep

This is where almost every home-built pantry cupboard goes wrong. People pick 60 cm deep, because that is the standard depth of a base unit, and then they end up with three rows of jars behind one another and only ever reach the front row.

The rule: shelves deeper than about 30 cm only work if you turn them into a drawer or a pull-out.

In practice you solve it like this:

  • Option A: a shallow cupboard (40 to 45 cm). Shelves 35 to 40 cm deep, everything in two rows at most, everything visible. My preference for most kitchens.
  • Option B: a deep cupboard (55 to 60 cm) with pull-outs at the bottom. Shallow fixed shelves plus door racks up top, drawers or pull-out shelves on runners down below. More volume, higher cost in hardware.
  • Option C: a deep cupboard with a shallow front zone. Shelves 30 cm deep with a 25 cm strip behind them that you deliberately use for big, rarely used items (the large pan, the Christmas serving dishes).

What you never do: 55 cm deep fixed shelves from top to bottom. That is the jumble cupboard.

Sizes: what do you go for?

Dimension Range Notes
Carcass height 190 to 220 cm Above 200 cm you need a step stool. Over 220 cm and it becomes awkward to move
Total height with plinth Carcass plus 8 to 15 cm A 15 cm plinth matches the standard kitchen plinth
Width 60 to 120 cm Over 100 cm, always two doors
Carcass depth 40 to 60 cm 45 cm is the sweet spot for most kitchens
Door rack depth 10 to 15 cm Any more will not clear the shelves
Shelf spacing, low 20 to 25 cm Tins, jars, boxes
Shelf spacing, high 30 to 40 cm Cereal, oil bottles, cornflake packets
Worktop height (for an internal surface) 90 to 95 cm In line with the usual kitchen worktop height of around 92 cm
Plinth height 10 to 15 cm Under the cupboard, gives you toe room

Measure your ceiling height before you start. A 220 cm cupboard that you assemble lying down will just about stand up in a room with a 240 cm ceiling. In a 230 cm room it will not, because the diagonal is longer than the height. The diagonal of 220 high by 45 deep is roughly 224.5 cm. It sounds obvious, but this is where people genuinely come unstuck.

Board thickness and span: the table nobody gives you

Sagging shelves are the most visible fault in a home-built cupboard. Food storage is heavy: a shelf full of tins and jars easily carries 25 to 40 kg.

Rules of thumb from real woodworking practice:

Material and thickness Safe span with heavy stores Notes
18 mm MDF up to approx. 50 cm MDF sags under its own weight and keeps creeping over time
18 mm chipboard/furniture board up to approx. 50 to 60 cm Same story, veneered or melamine-faced makes little difference
18 mm plywood (birch) up to approx. 60 to 70 cm Noticeably stiffer than MDF at the same thickness
22 mm MDF up to approx. 70 cm
22 mm plywood up to approx. 80 to 90 cm
18 mm solid timber up to approx. 70 to 80 cm Depends on the species and the grain

Is your cupboard wider than the safe span? Then you have three solutions:

  1. A centre divider. Put a vertical panel down the middle. It halves your span and makes the cupboard far stiffer straight away. Bonus: you can set different shelf heights left and right.
  2. A lip along the front. Glue a 20 x 40 mm strip of timber under the front edge of the shelf. That boosts stiffness enormously and looks tidy into the bargain.
  3. Thicker material. Simple, but heavier and dearer.

An important correction to a common misunderstanding: sagging is about stiffness, not strength. An MDF shelf will not break, it slowly droops and never comes back. So do not judge your shelf on “will it hold”, judge it on “will it stay straight”.

Choosing your material

Material Price Advantage Drawback Good for
Birch plywood 18 mm Mid to high Stiff, strong, attractive edge Dearer, the edge needs finishing Carcass and shelves, my preference
Furniture board (melamine-faced chipboard) Low Finished ready to use, cheap Less stiff, heavy, vulnerable to damp Carcass, short shelves
MDF 18 mm Low to mid Perfectly smooth, ideal for painting Sags, heavy, swells with damp Doors and fronts
Softwood panel (pine/spruce) Mid Warm, solid feel Moves (shrinks and swells), knots Visible parts, shelves
Poplar plywood Mid Light in weight Softer, dents more easily Back panel, drawers
Hardboard/HDF 4 mm Low Perfectly good back panel Back panel only Back panel

A smart combination: carcass in 18 mm birch plywood, doors in 18 mm MDF (lovely and smooth to paint), back panel in 6 mm plywood or hardboard, shelves in 18 mm plywood.

Example: a cutting list for a 90 x 210 x 45 cm larder cupboard

The starting point: carcass 210 cm high, 90 cm wide, 45 cm deep, 18 mm plywood, a 6 mm back panel in a rebate, a 12 cm plinth. In theory a centre divider would not be needed, but 90 cm minus 2 x 18 mm gives a shelf width of 86.4 cm. That is too much for 18 mm, so we do fit a centre divider and end up with two bays of about 42 cm. That sits comfortably inside the safe span.

Part Qty Size (mm) Material
Side 2 2100 x 450 18 mm ply
Bottom 1 864 x 450 18 mm ply
Top 1 864 x 450 18 mm ply
Centre divider 1 2064 x 450 18 mm ply
Adjustable shelf 8 420 x 430 18 mm ply
Back panel 1 approx. 2085 x 885 6 mm ply
Plinth front 1 900 x 120 18 mm ply
Door 2 approx. 447 x 2094 18 mm MDF
Door rack shelf 6 approx. 400 x 100 18 mm ply
Door rack lip 6 approx. 400 x 50 12 mm ply

Note: this is an example, not gospel. Check every dimension against your own ceiling height, your own boards and the actual thickness of those boards. Sheet material is rarely exactly 18.0 mm, so measure yours with a vernier caliper before you finalise the cutting list.

A tip that saves you hours: have the big sheets cut to size at the merchant or DIY store. You get squarer work than you will with a circular saw on a pair of trestles, and it solves the problem of getting them home.

Tools

  • Tape measure, pencil, try square, long straight edge or spirit level
  • Circular saw with a guide rail, or have it cut at the merchant
  • Drill driver plus pilot bits
  • A shelf-pin drilling jig (line boring jig). This is the tool that decides whether the job looks neat or bodged
  • 35 mm Forstner bit plus a hinge boring jig (for cup hinges)
  • Pocket-hole jig or biscuit joiner or dowelling jig (however you join the carcass)
  • Clamps, at least 4 long ones
  • Sander or sanding block, 120 and 180 grit
  • Brush, roller or spray gun
  • Drill plus masonry bit for the wall fixing

Step by step: how to build the larder cupboard

Step 1: Measure up and design

Measure the ceiling height, the width of the wall you have available and the doorway the cupboard has to get through. Draw the front elevation to scale, including the shelf spacing.

Look at the floor too. Is it out of level? Then plan for adjustable feet or packing blocks under the cupboard from the start.

Step 2: Decide your layout and shelf heights

Divide the cupboard into zones. More on that in the next section, but decide it now, because it determines where you drill your shelf-pin holes.

Rule of thumb for the split, top to bottom:
– Top 30 cm: rarely used, seasonal things
– Eye level (140 to 175 cm): everyday stores
– Worktop height (90 to 140 cm): breakfast things, appliances
– Bottom (up to 90 cm): heavy, bulky, drawers

Step 3: Cut all the parts

Cut everything in one session and label each part in pencil on the back. Check the diagonals of your big panels. If they match, it is square.

Step 4: Drill the shelf-pin holes

Do this before you assemble the cupboard. On a loose side panel on the bench it is easy, inside a finished carcass it is a nightmare.

The standard is System 32: 5 mm diameter holes, 32 mm centres, two rows per side (about 37 mm in from the front and back edges). Use a jig, drill with a depth stop set to around 12 mm, and do not go through the side.

Do the left-hand and right-hand sides with the same jig running the same way round, otherwise your shelves will sit skewed.

Step 5: Rout the rebate for the back panel

Rout a rebate of about 7 x 7 mm all round the back for a 6 mm back panel. That is neater and far stiffer than screwing the back on flat.

No router? Then the back can simply be screwed on. Just make sure it is dead square, because the back panel is what keeps the whole cupboard true.

Step 6: Assemble the carcass

Join the bottom, top and sides. Pick one method and stick with it:

  • Pocket holes: fast, strong, screws sit on the inside. The cheapest route.
  • Dowels: neat, invisible, demands accurate drilling.
  • Biscuits: mainly for alignment, plus extra glue area.
  • Screws through the side with cover caps: simple, visible, absolutely fine if you are painting.

Always glue as well. Assemble the carcass flat on a level floor, measure the diagonals and correct them before the glue grabs. Measure the diagonals. Every time. A carcass that is 5 mm out of square will never come right, no matter how much you adjust the hinges.

Then fit the back panel and the cupboard is rigid.

Step 7: Make and fit the plinth

Build the plinth separately as a little frame 12 cm high, set back slightly (about 4 to 6 cm) from the front face. The carcass sits on top of it.

The advantage of a separate plinth: you can level the cupboard by packing under the plinth, and your carcass stays clean.

Step 8: Stand the cupboard up and level it

Two people to lift it. Stand it against the wall and level it in both directions with packers under the plinth.

Level is not optional. Doors 2 m tall show up every bit of lean straight away in the gap.

Step 9: Fix the cupboard to the wall

Do this immediately, even if you were planning to “get round to it later”.

A tall cupboard full of stores is top heavy. A child hanging off an open door will tip it over. This is not a theoretical risk, it is the reason every manufacturer supplies anti-tip brackets.

Screw at least two solid angle brackets from the top of the carcass into the wall. Drill into masonry or concrete, or hit the studs in a timber wall. Use fixings that suit your wall. Aerated concrete or lightweight block needs special plugs.

Step 10: Hang the doors

For a door around 2 m tall you usually need four cup hinges. The exact number depends on door height and door weight, and manufacturers like Hettich and Blum have free online calculators for it. Take a minute to use one, it saves you a drooping door.

In practice:
– The hinge cup is a standard 35 mm diameter, about 12.5 mm deep.
– Set the top and bottom hinges about 80 to 100 mm in from the edge.
– Space the rest evenly.
– Bore the cup with a Forstner bit in a drill stand or with a hinge jig. Freehand will never come out square.
– Choose soft-close hinges. It saves the banging and it is kinder to your fixings.

Cup hinges adjust in three directions. Hang everything first, then adjust until the gap is even all round. Allow half an hour of fiddling for a perfect result.

Step 11: Make the door racks

This is the part that makes a larder cupboard a larder cupboard, and the part most self-builders skip.

  • Depth 10 to 15 cm, no more, or the rack will hit the shelves as the door closes.
  • Fit a retaining lip 4 to 6 cm high along the front, or run a thin steel cable or a wooden dowel across.
  • Fix them to the door with angle brackets or housed supports.
  • Check the clearance: measure the depth of your rack plus the depth of your internal shelves and keep at least 1 cm of play. Otherwise the door will not close.

What goes in them: herbs and spices, oil, vinegar, sauces, small jars. Everything that otherwise disappears at the back.

Step 12: Finishing

  • Sand everything smooth, 120 grit then 180. Ease all the sharp edges.
  • Plywood edges: cover with iron-on edging, or prime and sand again, or finish with a solid timber lipping.
  • Primer plus two coats of water-based paint, or emulsion with a hard-wearing topcoat. Water-based paint yellows less.
  • Inside: paint or clear lacquer. A smooth finish is easy to wipe clean, and that is exactly what you want in a food cupboard.
  • Bare timber in contact with food? Then use an oil or finish that the manufacturer explicitly states is suitable for food contact. If you would rather not, just keep everything in its packaging or in tubs so the food never touches the wood.

The layout: this is where the gains are

A larder cupboard is only good when you can work it blindfolded. Zones from top to bottom:

Zone 1: the top shelf (above 175 cm)
Rarely used items. Best china, big serving dishes, storage boxes you reach for twice a year. Do not put anything heavy up here, because you are lifting it above your head.

Zone 2: eye level (140 to 175 cm)
Your most-used dry goods. Pasta, rice, flour, tins. All visible in a single row.

Zone 3: the working zone (90 to 140 cm)
Breakfast things, coffee, tea. If you fit a pull-out or fixed surface at about 90 to 95 cm, this is where the toaster, the coffee machine or the mixer lives. Do not forget the socket in that case (more on that below).

Zone 4: the bottom (up to 90 cm)
Heavy and bulky. Crates of drinks, big bags, pans in a drawer. This works far better on drawers or pull-outs than on a fixed shelf.

Zone 5: the door racks
Small and flat. Spices, bottles, sauces, little jars.

What about the cool corner?

Traditional larders were cool. A modern one is not, because your kitchen sits at 20°C.

What the Dutch Nutrition Centre advises: products labelled “store in a cool place” belong in a cool, dark and dry space at roughly 15 to 20°C. Your food cupboard in the kitchen usually just about manages that, as long as it is not next to the oven or a radiator.

For potatoes and onions the ideal storage temperature is lower, around 4 to 10°C. You will not achieve that in a kitchen cupboard. The practical solution:

  • Put potatoes and onions in the coolest corner of your house: a cellar, an unheated utility room or the garage.
  • Store them in the dark, because light turns potatoes green.
  • Keep potatoes and onions apart. Potatoes give off ethylene gas, which makes onions spoil faster.
  • No cool space? Then count on about two to three weeks of life for ordinary potatoes at room temperature, and buy smaller quantities.

If you do want a cooler zone in the cupboard: make the bottom shelf from stone (an offcut of granite or composite works nicely), stand the cupboard against an external wall and fit a vent grille in the plinth and high up in the side. That gets you a few degrees below the rest of the kitchen. Do not expect a fridge, but you will notice the difference.

Extras that make the difference

Lighting. An LED strip on the inside of the front edge, with a door switch or a motion sensor. Costs a few pounds and makes the cupboard ten times more usable. Go for warm white (2700 to 3000 K) so it matches the kitchen.

A socket. If you want to use appliances inside the cupboard (coffee machine, toaster), you need a socket. Have an electrician install it if you do not know what you are doing. And be careful: appliances giving off heat and steam behind closed doors is a bad idea. Use them with the doors open, or build in ventilation openings.

A pull-out worktop. A board on heavy-duty drawer runners at about 90 cm. Pull it out when you are working, push it away when you are done. Choose runners with enough load rating and a lock in the extended position.

Ventilation. A few holes or a grille in the plinth and up top prevents stale air. Especially if you are keeping potatoes or onions in there.

Clear storage jars. Not a building tip, but the cheapest way to make a larder cupboard genuinely work. You can see at a glance what has run out.

Labels. Only works if your household keeps it up. Start small.

What does it cost?

These figures are a reasonable range, based on a cupboard of roughly 90 x 210 x 45 cm. Prices vary by supplier and by timber, so do your own sums.

Item Guide price Notes
Birch plywood 18 mm, approx. 3 sheets €250 to €450 The biggest cost, and the price swings a lot
MDF 18 mm for the doors €40 to €80
Back panel 6 mm €25 to €50
Cup hinges, 8 with soft close €40 to €100 The quality difference is large
Shelf supports €10 to €25 Buy spares
Handles, 2 €15 to €60
Screws, glue, edging tape €25 to €50
Primer and paint €50 to €100
Anti-tip brackets and fixings €10 Not the place to economise
LED strip with sensor €20 to €60 Optional
Total to build it yourself roughly €450 to €900 Depending on your material choice
Comparable off-the-shelf unit Often €800 to €2,500 Made to measure runs higher still

You can certainly do it cheaper: melamine-faced furniture board instead of birch plywood brings you down a good deal, and you do not have to paint it either. Just count on shorter safe spans, and therefore a centre divider.

The mistakes people make most often

  1. Building it too deep. 60 cm deep fixed shelves are a jumble cupboard. Stick to 40 to 45 cm or make it pull out.
  2. Ignoring the span. 18 mm MDF over 90 cm will sag inside a year. Put a centre divider in.
  3. Drilling the shelf-pin holes once the cupboard is up. Drill them in the loose sides, on the bench.
  4. Not fixing the cupboard to the wall. Tipping hazard. Always do it.
  5. Not measuring the diagonals while gluing up. An out-of-square carcass will never come right with hinge adjustment.
  6. Making the door racks too deep. More than 15 cm and the door will not close.
  7. Forgetting the diagonal when standing it up. A cupboard 220 high and 45 deep will not go upright in a room with a 224 cm ceiling.
  8. No ventilation. Stale air, and vegetables that spoil faster.
  9. Forgetting the plinth. Without one you stub your toes and you cannot level it on an uneven floor.
  10. Starting to build without settling the layout. Layout first, then drill.

Frequently asked questions

How deep should a larder cupboard be?

40 to 45 cm is the best depth for fixed shelves, because then you are never rummaging through two rows. If you want more volume, go to 55 to 60 cm but make the bottom half pull out with drawers or pull-out shelves. Deep fixed shelves are the most common design mistake there is.

How many hinges do I need for a 2 metre door?

Count on four cup hinges per door at that height, but the exact number also depends on the weight of the door and the type of hinge. Blum and Hettich have free online calculators where you enter height, width and weight. Take a minute over it, because a door that has drooped after a year is an annoying repair.

Which material is best for a larder cupboard?

18 mm birch plywood for the carcass and shelves is the best balance of stiffness, strength and price. MDF is lovely for doors because it paints up smooth, but less suited to long shelves because it sags. Melamine-faced furniture board is the cheapest route and needs no painting, but it is less stiff.

Do I have to fix a larder cupboard to the wall?

Yes. Always. A tall cupboard full of stores is top heavy and can tip, particularly if someone pulls on an open door. Two solid angle brackets from the top into the wall, with fixings suited to your wall type, cost a couple of pounds and ten minutes.

Can I store potatoes and onions in a larder cupboard?

Only if the cupboard is cool enough. The ideal storage temperature for potatoes and onions is around 4 to 10°C, and you will not get that in a heated kitchen. Keep them in a cellar, garage or unheated utility room instead, in the dark, and keep potatoes and onions apart because potatoes give off ethylene gas.

How long does it take to build a larder cupboard?

Allow two to three full days of building plus two days for painting and drying, assuming you have the material delivered cut to size. If you cut it yourself, add half a day. The biggest time sink is not the building, it is the finishing.

Can I turn an existing cupboard into a larder cupboard?

Absolutely. An old linen press or wardrobe is often exactly the right size. Take out the rail, drill shelf-pin holes in the sides, fit adjustable shelves, add door racks and paint the lot. Do check that the cupboard is rigid enough, and fix it to the wall.

To finish

A larder cupboard is one of the most rewarding furniture projects there is. It is not technically difficult, it is big enough to genuinely impress, and you use it every single day.

The three things that separate a good larder cupboard from a mediocre one: not too deep, shelves that do not sag, and door racks. The rest is measuring, cutting and painting.

And fixing it to the wall. Do not forget the wall fixing.


Would you rather not puzzle over sizes, cutting lists and layout yourself? At Fred’s DIY Plans you will find fully worked-out plans for cupboards and furniture, including a materials list and a cutting list, so you can get straight to work.

Browse the plans at Fred’s DIY Plans

Sources

Related articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Categories

.

Fred’s DIY Plans