You spend a weekend cutting concrete paving slabs for your patio. Or you drill twenty holes into a concrete wall for a kitchen renovation. The dust cloud slowly drifts away, you cough once, and carry on. No harm done, right?
Wrong. That dust cloud contains respirable crystalline silica — one of the most dangerous substances you can encounter as a DIYer. Microscopic particles that lodge deep in your lungs and never leave. The UK Workplace Exposure Limit (WEL) for respirable crystalline silica is 0.1 mg/m3 (8-hour time-weighted average), and the Health and Safety Executive (HSE) enforces COSHH regulations rigorously. Across the EU, the limit was halved to 0.05 mg/m3 in 2025, and there is growing pressure to align UK limits accordingly.
This article explains what silica dust actually is, which jobs put you at risk, and how to protect yourself without needing a full laboratory setup.
What is silica dust and why is it so dangerous?
Quartz is a mineral found in virtually all stone-based building materials. Concrete, brickwork, natural stone, tiles, sand-lime brick, aerated concrete, pavers — they all contain quartz. The silica content varies by material:
| Material | Silica content |
|---|---|
| Sandstone | 60 – 90% |
| Concrete | 25 – 40% |
| Brickwork | 15 – 35% |
| Natural stone (granite) | 20 – 45% |
| Sand-lime brick | 50 – 80% |
| Aerated concrete | 30 – 40% |
| Ceramic tiles | 10 – 30% |
| Sanitary ware (porcelain) | 15 – 25% |
The moment you drill, saw, grind or rout these materials, respirable crystalline silica is released. Particles smaller than 0.01 mm that you cannot see, smell or feel. They pass straight through your airways and settle in the alveoli of your lungs.
The treacherous part: you notice nothing. Not today, not next week. But after years of exposure it can lead to:
- Silicosis: irreversible scarring of lung tissue
- COPD: chronic obstructive pulmonary disease
- Lung cancer: respirable crystalline silica is classified as carcinogenic (Group 1)
- Autoimmune diseases: including rheumatoid arthritis and kidney problems
Silica dust has been classified by IARC (International Agency for Research on Cancer) in the highest risk group — the same category as asbestos.
Exposure limits and UK regulations
Under the Control of Substances Hazardous to Health (COSHH) Regulations, employers must control exposure to respirable crystalline silica. The current UK Workplace Exposure Limit is:
- UK WEL: 0.1 mg/m3 (8-hour time-weighted average)
- EU limit (since 2025): 0.05 mg/m3 (8-hour time-weighted average)
The EU limit stems from Directive 2017/2398 and reflects newer scientific evidence that the risk of lung cancer and silicosis remains too high even at the older thresholds. There is ongoing discussion about whether the UK will align with this stricter limit.
What does this mean for you as a DIYer?
Formally, workplace exposure limits apply to employers and employees. But the health risks are identical when you are cutting a concrete wall at home. The difference is that nobody is protecting you — except yourself.
The HSE actively inspects construction and renovation sites. Contractors, tilers and concrete drillers in particular face scrutiny. If you hire a tradesman who works on your kitchen without dust extraction, they could face significant enforcement action.
Which jobs are high-risk?
Not every job produces the same amount of silica dust. Below is a risk classification by activity.
| Activity | Material | Risk | Dust level without controls |
|---|---|---|---|
| Cutting concrete (angle grinder) | Concrete, tiles | Very high | 5 – 50x above the limit |
| Cutting tiles (dry) | Ceramic, natural stone | Very high | 10 – 30x above the limit |
| Raking out mortar joints | Brickwork | High | 5 – 20x above the limit |
| Drilling into concrete (hammer drill) | Concrete, sand-lime brick | High | 3 – 15x above the limit |
| Demolishing walls (breaking out) | Brickwork, concrete | High | 5 – 25x above the limit |
| Sanding / surface grinding | Concrete floor, render | High | 5 – 20x above the limit |
| Drilling into brick | Brickwork | Moderate | 2 – 8x above the limit |
| Drilling tiles (diamond core bit) | Ceramic | Moderate | 2 – 5x above the limit |
| Sanding plasterboard | Plaster (low silica content) | Low | At or below the limit |
One thing stands out: almost anything you do with concrete and stone exceeds the exposure limit. Even drilling a few holes in a concrete wall for a TV bracket generates dust concentrations above 0.1 mg/m3.
Dust-free working: controls in order of effectiveness
The best protection is to produce no dust at all. The next best is to capture dust at source. Only then comes personal protection. This is called the “hierarchy of controls” and it is the approach the HSE requires.
1. Source control: wet working
The most effective way to suppress silica dust is water. Wet working reduces dust emissions by 80 to 95%.
- Wet tile cutting: use a tile saw with a water tray or an angle grinder with a water feed attachment (costs around £12 – £25)
- Wet drilling: diamond core bits with water feed, or simply a sponge held above the drill hole by a helper
- Wet grinding: angle grinder with a water shroud (available from around £15)
Note: wet working and electricity do not always mix safely. Only use tools rated for wet work, or ensure you have a 30 mA RCD (residual current device) in place.
2. On-tool dust extraction
Cannot work wet? Then on-tool extraction is the next best option. You connect a vacuum to your tool so that dust is captured right where it is produced.
- Construction dust extractor (M-class or H-class): mandatory for silica dust. A standard household vacuum blows the fine particles straight back out of the exhaust
- Dust extraction collar for drills: dedicated attachments for hammer drills (from around £8)
- Dust shroud for angle grinder: extraction shrouds that mount on the grinder and connect to the dust extractor
Important: a dust extractor for silica must be at least M-class (filters 99.9% of particles > 0.3 micrometres). For intensive work with high silica content, H-class (99.995%) is better. Check for the appropriate rating.
3. Personal protective equipment (PPE)
As a third layer: personal protection. PPE is not a substitute for source controls — it is an addition.
Respiratory protection:
| Mask type | Protection factor | Suitable for | Price |
|---|---|---|---|
| FFP2 disposable mask | 10x the limit | Brief drilling, light dust | £0.50 – £2 each |
| FFP3 disposable mask | 30x the limit | Drilling, light grinding | £2 – £4 each |
| Half-face respirator + P3 filter | 30x the limit | Prolonged grinding, routing | £20 – £40 (respirator) + £7 – £12 (filters) |
| Full-face respirator + P3 filter | 400x the limit | Intensive demolition, dry cutting | £70 – £170 |
| Powered air-purifying respirator (TH2P) | 50x the limit | Working in dust all day | £170 – £500 |
Which mask you need depends on the activity. For drilling a few holes in concrete, an FFP3 mask is sufficient. If you are cutting tiles dry for an entire afternoon (which you really should not be doing), you need at least a half-face respirator with a P3 filter.
Other PPE:
- Safety goggles (sealed type): prevents dust entering via your eyes
- Work gloves: prolonged contact with silica dust can also cause skin irritation
- Long-sleeved workwear: dust on your clothes follows you indoors. Shake off or wash separately
Tip: always combine
The golden combination for a DIYer: wet working OR on-tool extraction + FFP3 mask + safety goggles. That might cost you £25 – £40 in disposables for a weekend of work, but your lungs are irreplaceable.
What does it cost to work safely?
A common excuse: “All that safety gear is expensive.” Let us do the maths.
| Equipment | One-off / reusable | Cost |
|---|---|---|
| FFP3 disposable masks (10 pack) | Disposable | £15 – £30 |
| Half-face respirator + P3 filters | Reusable (replace filters) | £30 – £55 |
| Sealed safety goggles | Reusable | £7 – £17 |
| M-class dust extractor | Reusable | £130 – £300 |
| Dust shroud for angle grinder | Reusable | £20 – £50 |
| Water feed kit for grinder | Reusable | £12 – £25 |
| Diamond core bit with water connection | Reusable (wears down) | £12 – £35 per bit |
| Dust extraction collar for drill | Reusable | £8 – £20 |
Basic kit for the occasional DIYer (drilling and grinding a few times a year):
FFP3 masks + safety goggles + drill extraction collar = around £30 – £70
Extended kit for the active renovator (kitchen/bathroom renovation):
Half-face respirator + M-class dust extractor + grinder dust shroud + safety goggles = around £190 – £420
For comparison: a kitchen renovation easily costs £8,000 to £25,000. That £250 for safe equipment is less than a bunch of flowers on the worktop.
Practical: how to tackle common jobs
Drilling holes in concrete or masonry
- Use a hammer drill with a dust extraction collar
- Alternatively: have someone hold a vacuum nozzle just below the drill hole
- Wear an FFP3 mask
- For more than 10 holes: consider a drill with integrated extraction (Hilti, Bosch and Makita all offer systems for this)
Cutting tiles
- Always use a tile saw with a water tray. Dry cutting is an absolute no-go
- When using an angle grinder: water shroud or at the very least a dust extraction shroud
- Work outdoors if possible
- FFP3 mask, even when wet cutting (some residual dust is always released)
Cutting concrete or brickwork
- Angle grinder with dust shroud, connected to an M-class dust extractor
- Alternatively: wet cutting with a water shroud
- FFP3 mask as a minimum; half-face respirator for prolonged work
- Sealed safety goggles
- Work outdoors or in a well-ventilated space
Floor grinding (concrete floor, cement screed)
- Use a floor grinder with connected dust extraction
- An M-class dust extractor is essential here
- Half-face respirator with P3 filter (this is prolonged work with heavy dust)
- Seal the room off from the rest of the house (plastic sheeting over doorways)
Raking out mortar joints
- Mortar raker with dust extraction
- FFP3 mask as a minimum
- Work outdoors if possible
- After raking: do not sweep (that puts dust back into the air) — vacuum with an M-class extractor
Common mistakes
-
“I’m working outside, so the dust blows away” — working outdoors helps, but the dust concentration right next to your face is still high. Always wear a mask.
-
“I’ll hold my breath” — drilling a hole takes longer than you can hold your breath. And the dust cloud lingers for minutes.
-
“I’ll use a normal vacuum cleaner” — household vacuums filter particles down to about 5 micrometres. Silica dust is 10 to 100 times smaller. You are simply blowing the fine dust back into the room.
-
“Surely a surgical face mask is good enough?” — no. Surgical masks are designed to stop droplets, not fine dust. They do not seal around your face. Use FFP2 as an absolute minimum, preferably FFP3.
-
“I’m only doing it once” — true, but if you do a few jobs each year without protection, the exposure accumulates. The damage to your lungs is cumulative and irreversible.
Checklist: working safely with silica dust
Before you start any job involving concrete, stone or tiles:
- [ ] Can I work wet? If yes: arrange water supply
- [ ] Can I use on-tool dust extraction? If yes: M-class dust extractor + correct attachment
- [ ] Do I have the right mask? (FFP3 minimum for short jobs, half-face respirator for longer ones)
- [ ] Am I wearing sealed safety goggles?
- [ ] Am I working in a ventilated space or outdoors?
- [ ] Have I sealed the room off from the rest of the house? (for indoor work)
- [ ] Do I know how to clean up afterwards? (vacuum, do not sweep)
- [ ] Does my mask fit properly? (no beard, nose bridge pressed down, no air gaps)
Frequently asked questions
Is silica dust only dangerous with prolonged exposure?
Every exposure contributes to damage. There is no safe lower threshold. The risk increases with duration and frequency, but even a single high exposure (such as a full day of dry tile cutting) can cause harm.
Do I have to comply with the workplace exposure limit as a private individual?
Legally, no. The WEL applies to employers. But your lungs do not distinguish between work and hobby. The health risks are identical.
Can I use an M-class dust extractor for other jobs?
Absolutely. An M-class dust extractor is also ideal for wood sanding dust, plaster dust and general construction dust. It is one of the best investments you can make as a DIYer.
How do I know if my dust extractor is suitable?
Check the dust class on the rating plate. L-class is for low risk (wood dust), M-class for medium risk (silica dust, hardwood dust), H-class for high risk (asbestos). For silica dust you need at least M-class.
What if my tradesman works without protection?
Raise it with them. The HSE enforces COSHH regulations and can take action against tradespeople who fail to control dust exposure. A contractor cutting concrete without dust extraction is breaking the law. You have every right to insist that work is carried out safely in your home.
Are silicosis and pneumoconiosis the same thing?
Silicosis is a specific form of pneumoconiosis caused by silica (crystalline quartz) dust. Pneumoconiosis is the umbrella term for lung diseases caused by inhaling fine dust. Silicosis is one of the most serious forms.
Sources
- HSE: Silica — Health and Safety Executive guidance
- COSHH Regulations (Control of Substances Hazardous to Health)
- IARC Monographs on the Evaluation of Carcinogenic Risks to Humans, Volume 100C
Check out our DIY plans at FredsDIYPlans.com for more home improvement projects.
