Gas is getting more expensive. Energy bills are rising. And more and more homeowners are looking at alternatives they can install themselves, without having to replace an entire heating system.

Infrared panels are one such alternative. They heat objects and people rather than air, run on electricity, and you can hang them yourself. No pipework, no boiler, no installer you have to wait three weeks for.

But there are things you need to know before you start. How many watts do you need per room? Can you connect multiple panels to the same circuit? And is it really cheaper than gas?

In this article you will learn exactly how infrared heating works, how to mount panels yourself on a ceiling or wall, what the maximum load per circuit is, and how the costs compare between gas and infrared. Including concrete calculations.

How does infrared heating work?

Infrared heating works fundamentally differently from a traditional gas boiler with radiators. A radiator heats the air in a room. That warm air rises, cools, sinks and is heated again. This uses a lot of energy and produces uneven warmth: warm at the ceiling, cold at the floor.

An infrared panel emits infrared radiation. This radiation does not heat the air but the surfaces it strikes: walls, floor, furniture and your body. Those objects then gradually release the warmth into the room. The effect is comparable to sunlight: you feel the warmth directly, even when the air temperature is relatively low.

This has three practical advantages:

Infrared panels run on electricity. They need no gas connection, no pipework and no water. You plug them into an ordinary socket or wire them directly to a circuit in your consumer unit.

What wattage do you need per room?

Before ordering panels, you need to know how many watts you require. That depends on three factors: the floor area, the level of insulation, and whether the panel is the primary or supplementary heat source.

Rule of thumb for well-insulated homes (EPC rating B or better):

Room Floor area Required wattage Recommended panel
Bedroom 12 m2 600 – 720 W 1x 700 W
Living room 30 m2 1,500 – 1,800 W 2x 800 W or 3x 600 W
Bathroom 6 m2 350 – 450 W 1x 400 W (with towel rail)
Office/study 10 m2 500 – 600 W 1x 600 W
Kitchen 15 m2 750 – 900 W 1x 900 W or 2x 450 W

With moderate insulation (EPC rating C-D): allow 75-85 watts per m2.
With poor insulation (EPC rating E or lower): allow 100-120 watts per m2. In that case, consider insulating first — otherwise electricity costs will be too high.

When in doubt, choose slightly more wattage. A panel with a thermostat switches itself off once the desired temperature is reached. A panel that is too small runs all day and ultimately uses more energy.

Mounting infrared panels yourself: step by step

You do not need a technical background to mount infrared panels. Most panels come with a complete mounting kit. What you need:

Tools:
– Drill with masonry bit (6 mm or 8 mm, depending on wall plugs)
– Spirit level
– Pencil
– Screwdriver
– Tape measure

Step 1: Determine the position

Ceiling mounting is the most effective. The radiation then falls downward onto the floor, furniture and people, giving the most even heat distribution.

Wall mounting also works, but the radiation mainly reaches the opposite side of the room. When wall-mounting, hang the panel at least 15-20 cm below the ceiling and never behind furniture.

For ceiling mounting: choose a position above the area where you want to feel the warmth. In a living room that is above the seating area. In a bedroom, above the bed.

Step 2: Mark the fixing points

Hold the supplied bracket against the ceiling or wall. Use a spirit level to keep the bracket straight. Mark the drill points with a pencil.

For ceiling mounting: check that there are no pipes or cables at the point where you intend to drill. Use a cable detector if necessary.

Step 3: Drill and plug

Drill the holes at the marked points. Use wall plugs suited to your ceiling or wall type:

Note: an infrared panel weighs on average 3-8 kg. For ceiling mounting into plasterboard, you must be sure the fixing can support the weight. If in doubt, always use toggle bolts or locate the joists.

Step 4: Fit the bracket and hang the panel

Screw the bracket in place. Hang the panel on the bracket. Most panels click into place or are secured with a small locking screw.

Step 5: Connect the panel

The simplest method: plug the plug into the socket. Most infrared panels are supplied with a standard plug and cable.

Want a neat installation without visible cables? Then you can hard-wire the panel to a fused connection unit or a back box. This is not difficult, but you need to know what you are doing. More on this in the next section.

Connecting an IR panel: hard-wiring and circuit loading

Plugging an infrared panel into a socket is something anyone can do. But if you want to hard-wire multiple panels, or need to know how many panels you can put on one circuit, you need to do a little maths.

Maximum load per circuit

A standard circuit in a consumer unit is protected by a 32A MCB (ring main) or a 20A MCB (radial) and wired with appropriate cable. For a dedicated radial circuit on a 20A MCB with 2.5 mm2 cable:

20 amps x 230 volts = 4,600 watts

That is the theoretical maximum. In practice you should not use more than 80% of the maximum load for continuous operation (and infrared panels run for extended periods). That means:

Practical maximum: 3,680 watts per circuit

So on a dedicated circuit you can run:
– 4x 700W panels (2,800W) — fine
– 3x 900W panels (2,700W) — fine
– 5x 600W panels (3,000W) — fine
– 6x 600W panels (3,600W) — close to the limit, still within the 3,680W practical maximum

Hard-wiring

Want to hard-wire panels without a plug? Then you connect the panel cable to a fused connection unit or a back box behind the panel. Most panels have a terminal block with three connections: live (brown), neutral (blue), and earth (green/yellow).

Important: In the UK, electrical work in your home must comply with Part P of the Building Regulations. You can do minor electrical work yourself (such as adding a fused spur from an existing circuit), but notifiable work — such as adding a new circuit — must be carried out or certified by a registered electrician. If in doubt, hire a qualified electrician for the entire job.

Adding a dedicated circuit?

If you have infrared panels in multiple rooms, it is sensible to have a dedicated circuit added to your consumer unit. Advantages:

An electrician typically charges between £150 and £250 for adding a circuit, including the MCB and cabling.

Infrared vs. gas: what does it cost?

This is the question everyone asks. The answer depends on your situation, but we can work with averages.

Worked example: living room of 30 m2

Assumptions:
– Well-insulated home (EPC rating B)
– 1,600 watts of infrared panels in the living room
– Thermostat controlling the panels 8 hours per day
– Panels run on average 50% of that time (cycling on/off)
– Heating season: 200 days per year

Comparison of costs between gas heating and infrared heating in a table

Gas heating Infrared heating
Energy source Mains gas Electricity
Consumption per day ~4 m3 gas (~40 kWh) ~6.4 kWh electricity
Price per unit (2026) ~£0.07/kWh (gas) ~£0.24/kWh (electricity)
Cost per day £2.80 £1.54
Cost per heating season £560 £308
Purchase (living room only) Existing installation £350 – £700 (2 panels + thermostat)
Payback period n/a Within 1 year

Caveat: This calculation applies to a well-insulated home with a living room that you heat zonally. If you want to heat an entire house using only infrared, electricity costs will be higher. The strength of infrared panels lies precisely in zonal heating: heating only where you are.

When does infrared pay off most?

When is gas still cheaper?

Do it yourself or hire someone?

Installing infrared panels is one of the few heating solutions you can genuinely do yourself. But not everything needs to be DIY.

What you can do yourself:
– Hanging panels on wall or ceiling
– Plugging panels into an existing socket
– Pairing a thermostat (wireless, plug-in)

What you are better off hiring out:
– Running fixed wiring behind the wall or through the ceiling
– Adding a dedicated circuit in the consumer unit
– Connection to the consumer unit

Cost indication for professional installation:
– Hanging + hard-wiring per panel: £65 – £110
– Adding a dedicated circuit: £150 – £250
– Complete installation (3 panels, hard-wired, dedicated circuit): £350 – £550

If you are handy and only want to plug the panels into sockets, you save all those costs. The mounting itself is no more complicated than hanging a heavy mirror.

Frequently asked questions

Can I mount an infrared panel on any ceiling?

Yes, provided the ceiling can support the weight (3-8 kg). With concrete ceilings that is no problem. With plasterboard ceilings you need to screw through the plasterboard into the structure behind, or use dedicated plasterboard fixings.

How many infrared panels do I need for my whole house?

That depends on the number of rooms, the floor area and the insulation level. For an average terraced house (100 m2, EPC B), allow 5,000 to 7,000 watts in total. That is 7 to 10 panels, spread across the rooms you actually heat.

Am I allowed to hard-wire an infrared panel myself?

In the UK, you can carry out minor electrical work yourself, such as adding a fused spur from an existing circuit. However, notifiable work under Part P of the Building Regulations — such as adding a new circuit — must be done or certified by a registered electrician. Plugging panels into a socket is always permissible.

Do I need a dedicated circuit?

Not necessarily. If the total load stays under the circuit’s maximum capacity and there are no other heavy consumers on it, you can connect the panels to an existing circuit. With more than 3 panels, a dedicated circuit is advisable.

Does infrared heating work in an uninsulated shed or garage?

It can, but it is not efficient as a primary heat source. In an uninsulated space, warmth escapes too quickly. Infrared does work well if you only want to heat the sitting area: the radiation warms you directly, regardless of the air temperature. For a workshop where you sit in one spot, a targeted panel can work perfectly well.

Can I combine infrared panels with my gas boiler?

Yes. Many people use infrared panels as supplementary heating. The boiler provides the base warmth; infrared adds extra heat where needed. This is a sensible stepping stone if you do not want to go fully off gas in one go.

Conclusion

Installing infrared panels is one of the most accessible ways to save on gas costs and take a step towards electric heating. The mounting is simple enough to do yourself, the cost per room is manageable, and the payback period is short.

The key is in the right approach: calculate the required wattage per room, check that your circuit can handle the load (practical max around 3,680W for continuous use), and choose ceiling mounting where possible.

Start with one or two rooms. Measure the difference on your energy bill. Then expand if it suits you. That is the beauty of infrared panels: you do not have to replace your entire heating system in one go.


Check out our DIY plans at fredsdiyplans.com for more home improvement projects.

Leave a Reply

Your email address will not be published. Required fields are marked *