You want to build a wooden sliding door that glides along the wall. That industrial black-steel-and-scaffold-board feel, without a swing door eating up half your room.
Good plan. And it’s more doable than you think.
In this article you’ll build an surface-mounted sliding door (the loft door or barn door) with a top track, right alongside me. From the first measurement to the last screw.
Quick answer: how do you build a sliding door?
Make the door 5 to 10 cm wider than the wall opening, so it overlaps on both sides and closes off neatly. Build it from scaffold board or softwood with a Z-frame or frame construction on the back to stop it warping.
Never screw the track straight into plasterboard. Fix it into a solid timber batten or load-bearing beam behind the board. Choose a track system with a load capacity well above the door weight (reckon on 18 to 25 kg per m² of door).
Building it yourself in 2026 costs roughly 120 to 250 euros for track, timber and hardware. A day’s work, plus drying time for the glue.
What types of sliding door are there?
Not every sliding door is the same. Before you start cutting, choose the type.
| Type | How it works | Who it’s for |
|---|---|---|
| Surface-mounted / barn door (top track) | Door hangs from a visible track above the opening, slides along the wall | DIYers, industrial look, easiest to build yourself |
| Pocket / cassette | Door disappears into a hollow wall (a cassette inside the metal-stud frame) | Clean finish, but has to be planned in during the build |
| Wardrobe sliding door | Light doors in a bottom and top track of a cupboard or alcove | Walk-in closet, space saving in small rooms |
This article is about the first one: the surface-mounted barn door. That’s the version you build yourself without breaking the wall open.
A pocket door sounds nice, but the wall has to come open for it. That’s a renovation, not a weekend job.
Getting the size right: this is where it goes wrong
This is where most people trip up. The door isn’t as wide as the opening. It’s wider.
Width of the door
Measure the opening and add 5 to 10 cm on every side. So an opening of 80 cm becomes a door of 90 to 100 cm wide.
That overlap does two things: it covers the gap so you can’t see past it, and it stops draughts and prying eyes.
Height of the door
Measure from the floor to where your track will go. Leave 8 to 12 mm clear at the bottom, so the door doesn’t drag across the floor.
The track usually sits about 40 to 50 mm above the door. So reckon: door height + clearance under the door + track height = the total height you need above the opening.
Free space beside the opening
Almost everyone forgets this. Beside the opening you need at least the width of your door free against the wall. Otherwise the door can’t open fully.
Door of 100 cm? Then you need 100 cm of free, flat wall next to it. No light switch, no radiator, no frame in the way.
Tip: first lay out the outline on the wall with masking tape. That way you’ll see straight away whether the door fits in both the open and closed position, before you cut a single board.
Building the door itself (and keeping it from warping)
Scaffold board and softwood are popular because they’re cheap, easy to work with, and that grey patina looks good in a modern interior. But solid wood moves: it warps if you do nothing.
The solution is a frame on the back.
The Z-frame or frame construction
You lay the vertical boards side by side for the visible face. On the back you screw cross battens: one at the top, one at the bottom, and a diagonal between them. That’s the classic barn-door Z.
The diagonal isn’t decoration. It stops the door hanging like a parallelogram and sagging. Always run the diagonal from the bottom on the hanging side up towards the top, so it carries the load rather than pulling along with it.
Glue and screw
Glue the face boards together with D3 wood glue and press them with clamps. Let that dry overnight.
Then screw the frame onto the back. Always pre-drill with a thin bit, otherwise scaffold board splits.
Fit the boards with the grain alternating (the growth rings facing forward and backward in turn). That keeps the door flatter.
Choosing the track system: load capacity versus weight
The track has to carry the door. Sounds obvious, but this is where it goes wrong if you buy a set that’s too light for a heavy oak door.
How do you estimate your door’s weight?
Reckon roughly with these figures per square metre of door surface (boards around 20 mm thick):
| Wood type | Weight per m² |
|---|---|
| Softwood / scaffold board | approx. 12 to 16 kg |
| Douglas fir | approx. 15 to 18 kg |
| Oak (solid) | approx. 22 to 28 kg |
A scaffold-board door of 1.00 x 2.15 m (2.15 m²) therefore weighs roughly 26 to 34 kg. Add the hardware and glue and you’re at around 35 kg.
Which track?
A standard hanging track system with two rollers often carries up to 100 or 125 kg. Plenty for a wooden barn door. Deliberately choose a set with a load capacity well above your estimated weight, not just over it.
Also watch the track length: it has to be at least twice the door width, otherwise the door won’t slide fully open.
The crucial point: where do you fix the track?
This is the most important part of the whole project. Skip the rest, but read this.
Not into plasterboard. Never.
A plasterboard wall won’t carry your 35 kg door. The plugs tear out over time and your door comes down. Plasterboard plugs are for small pictures, not for sliding doors.
Into a load-bearing beam or timber batten instead
Behind the plasterboard sit vertical timber or metal studs (at around 40 or 60 cm centres). That’s where you need to go.
Three safe ways:
-
Straight into a concrete or masonry wall: drill with a hammer drill, use solid plugs (8 mm or thicker) and screws. The strongest.
-
Into the timber studs behind the plasterboard: track them down with a stud finder, screw the track across into every stud you hit. Long screws that go through the board and grip into the wood.
-
With a continuous mounting batten (recommended): first screw a solid timber batten (for example 27 x 70 mm or thicker) horizontally along the full length, into the studs or wall. Then screw your track into that batten. That way you spread the load and you can never get it wrong.
That mounting batten often disappears behind the track, or you give it the same colour. Problem solved, and your door hangs for years.
Floor guide and soft-close
The door now hangs from the top track. But at the bottom it can swing freely back and forth against the wall. Annoying, and it damages your wall.
Floor guide
A floor guide is a small pin or guide block on the floor or skirting, running in a groove at the bottom of the door. The door can still slide, but it no longer wobbles forward.
Rout or cut a shallow groove in the bottom edge of the door (a few mm deep) and screw the guide in the right spot. It costs a few euros and is almost essential.
Soft-close dampers
Optional, but nice. Soft-close dampers catch the door at the end, so it doesn’t slam against the end stop and closes gently.
You buy them as a separate kit to suit many track systems (around 20 to 40 euros). For a heavy door or a child’s room, recommended.
Step-by-step: building a sliding door in 8 steps
Tools you’ll need:
- Tape measure, pencil and spirit level
- (Hammer) drill and screwdriver
- Circular saw or hand saw
- Clamps
- Stud finder (to locate the studs)
- Thin pilot drill bit, plus a bit to suit your plugs
- Sander
The steps:
-
Measure and calculate. Opening + 5 to 10 cm per side for the width. Check the free wall beside it with masking tape.
-
Cut the face boards to door width and height. Lay them side by side, grain alternating.
-
Glue the boards with D3 glue, clamp them together and let them dry overnight.
-
Screw the frame (top, bottom, diagonal) onto the back. Pre-drill to stop splitting.
-
Sand the door smooth and lightly round the edges.
-
Finish the door (see below) and let it dry.
-
Fit the mounting batten and track. Locate the studs, screw the batten on level, screw the track onto it. Keep to the right height (door height + clearance under + ~45 mm).
-
Hang the door, fit the rollers, click it onto the track, fit the end stops, the floor guide and soft-close if you want.
Done. Slide it back and forth once and enjoy.
Finishing
Scaffold board with a patina you often just leave as it is, perhaps with a colourless matt stain or oil against dirt and drying out.
Want it sleek? A few coats of clear varnish or a transparent wood oil. For the dark look, use a black stain or an industrial wood wax.
Don’t forget the edges and the back, otherwise the door takes up moisture there and starts to move after all.
2026 costs: what are you looking at?
Prices rise with wood type and track quality. A realistic budget for a door of roughly 100 x 215 cm:
| Component | Build it yourself (2026) |
|---|---|
| Track system (track + rollers + stops) | 60 to 130 euros |
| Timber (scaffold board/softwood) | 40 to 80 euros |
| Screws, glue, mounting batten | 15 to 25 euros |
| Floor guide | 5 to 15 euros |
| Soft-close (optional) | 20 to 40 euros |
| Total to build yourself | around 120 to 290 euros |
For comparison: a ready-made wooden barn door with hardware, ordered to size, quickly comes to 350 to 700 euros or more.
So building it yourself saves you a fair bit, and you decide the width, colour and wood type yourself.
Frequently asked questions
How much wider should a sliding door be than the opening?
5 to 10 cm wider than the opening on each side. An opening of 80 cm therefore calls for a door of 90 to 100 cm. That overlap covers the gap and stops prying eyes and draughts.
Can I screw a sliding door track into plasterboard?
No. Plasterboard won’t carry the weight and the plugs tear out. Always screw the track into a masonry wall, into the timber studs behind the board, or into a continuous mounting batten that you first fix into those studs.
How heavy can my wooden sliding door be?
Reckon on 12 to 28 kg per m², depending on the wood type. A scaffold-board door of just over 2 m² weighs around 30 to 35 kg. Most standard track systems carry 100 to 125 kg, so that’s well within range. Always choose a track with a load capacity comfortably above your door weight.
How do I stop my homemade sliding door from warping?
Build a frame on the back with a diagonal (the Z-frame), glue and screw the boards, fit the grain alternating, and finish every side of the door against moisture uptake. Pre-drilling prevents splitting.
Do I need a floor guide?
Yes, almost always. Without a guide the bottom of the door swings against the wall. A floor guide runs in a shallow groove in the bottom edge and keeps the door stable, while it carries on sliding.
What does it cost to build a sliding door yourself in 2026?
Reckon on 120 to 290 euros for track, timber and hardware together for a door of roughly 100 x 215 cm. A ready-made barn door made to size starts around 350 euros and rises to over 700 euros.
Ready to start? With a good build plan to hand, you’ll know exactly which measurements, battens and screws you need, and you’ll avoid miscalculations before you cut.
Take a look at the sliding door and furniture plans at fredsdiyplans.com and build your barn door right the first time.
