Painting window frames: how to get a crisp, long lasting finish

Facebook
Twitter
LinkedIn
Pinterest

Short answer first: painting window frames always follows the same order. You clean and degrease the timber, sand the old coat back to a matt finish, repair holes and loose patches, prime any bare wood, and then lay on two thin coats of topcoat with a light sand in between. Always lay off in the direction of the grain, and don’t work in full sun or damp weather.

Sounds simple, and mostly it is. The difference between a frame that still looks good in ten years and one that flakes after two winters comes down to preparation and the weather. Those are exactly the two things most people half skip.

Below you’ll find, step by step, how to paint wooden window frames, windows and doors. With the right materials, specific sandpaper grits and drying times, the best temperature for working outside, the mistakes that make paint let go, and an honest look at costs.

When is it time to repaint your window frames?

Good exterior paintwork lasts five to eight years on average, and with top quality paint in ideal conditions sometimes up to ten. Indoors you won’t need to go again for about seven to ten years. A translucent wood stain needs more frequent maintenance than an opaque paint, because the thinner, less pigmented film weathers faster.

Don’t wait until the paint has come off completely. The longer you put it off, the more prep work you create and the bigger the risk of rot. These are the signs your frames are due for a coat:

  • The sheen has gone and the paint feels dull and chalky
  • The paint is flaking, cracking or lifting in patches
  • You can see hairline cracks in the film, especially on the top rail and the bottom corners
  • The timber is going grey or feels soft (watch out for rot)
  • The sealant beads around the glass are lifting or have dried out

The bottom of the frame and the joints under the glass take the worst punishment, because that’s where water sits longest. Check those spots first.

Already got rot in the frame? Then painting over it is pointless. Affected timber simply carries on rotting under the new paint. Fix that first. How to tackle wood rot, and when a frame is better off replaced, is covered in our separate article on the subject.

What’s the best season and temperature for painting outside?

This is the part that decides between success and failure, and where a lot of DIYers come unstuck. Paint needs the right conditions to flow out and bond properly.

The safe range for exterior work is between 10 and 20 degrees, with around 18 degrees as the sweet spot. Below 5 degrees you don’t start at all, and above 25 degrees you’re better off waiting. Some specialist winter paints, such as Sikkens Rubbol SB, tolerate a wider band of 0 to 30 degrees, but those are exceptions you’ll find stated on the tin.

Alongside temperature, humidity counts. Keep relative humidity below 85 per cent, with 40 to 70 per cent as the ideal. And one firm trade rule: the surface must be at least 3 degrees above the dew point. Otherwise moisture will settle on your fresh coat.

Right conditions for painting outside10-20 °CSafe temperature range forexterior work18 °CSweet spot for paint to flowout and bond< 85%Maximum relative humidity3 °CMinimum the surface must beabove the dew point
Check the weather against these numbers before you open the tin.

What goes wrong in the wrong conditions:

Condition What happens
Too cold (below 5 °C) Paint dries far too slowly, more than 24 hours between coats
Too warm or full sun Paint dries too fast, giving brush marks, wrinkling and visible lap marks
Too damp, above 85% Drying slows down, risk of dull patches and blistering
Rain or dew soon after painting The still wet film washes off or goes matt

In practice that means late spring and early autumn are often ideal. In summer, paint early in the morning or towards evening, and follow the sun around the house so you never work in direct sunlight. Never paint just before forecast rain either, and make sure the timber is genuinely dry. Painting wet wood guarantees flaking paint, because the moisture will find its way out straight through your paint film.

What materials and tools do you need?

The right kit saves you a lot of frustration. Here’s your list:

  • Primer for bare timber and repaired areas
  • Topcoat, water based (acrylic) or solvent based (alkyd)
  • A flat brush or block brush, in a width that suits your frame
  • Sandpaper: coarse (120 grit) for loose paint and rough timber, medium (180 to 220) for prep, fine (320 to 400) for sanding between coats
  • A sanding block or sanding sponge for even pressure
  • Filler or wood filler for holes and damage
  • Paintable acrylic sealant for joints (not silicone)
  • Degreaser or sugar soap to shift grease and grime
  • A paint scraper and possibly a heat gun for loose paint
  • Masking tape and dust sheets for glass, ironmongery and walls
  • A dust cloth or tack cloth to lift sanding dust

About that brush: with water based acrylic paint you’ll get on best with a synthetic filament brush. With solvent based alkyd, a natural bristle or mixed bristle brush performs better. A good brush is worth it, because a cheap one sheds hairs and leaves brush marks.

And don’t buy a bargain bin tin of paint. Quality paint bonds better, covers better and stands up far longer outside in rough weather. Your window frames are not the place to economise.

Water based or alkyd: which paint should you choose?

This is the question everybody asks. The two types differ quite a bit.

Alkyd paint (solvent based) penetrates deeper into the timber, gives a hard, beautifully flowing film and covers strongly. Downsides: it smells strongly while you work, it’s less environmentally friendly, and it yellows over time, especially in spots that get no daylight. Drying time is long.

Water based paint (acrylic) dries fast, barely smells, hardly yellows and is kinder to the environment. The quality of modern water based exterior paint is excellent these days. You can keep working sooner, and you rinse the brush out with water.

Feature Water based (acrylic) Alkyd (solvent)
Drying time Fast Slow
Smell Slight Strong
Yellowing Hardly any Yes, over time
Environment Better Heavier impact
Cleaning the brush With water With white spirit/thinner
Curing Takes longer to harden right through Goes hard

Legislation plays a part too. In the Netherlands, professional decorators have only been allowed to use water based paint indoors since 1 January 2000, because of volatile organic compound (VOC) emissions. For exterior work, alkyd is still permitted there for professionals. As a private individual you can buy either, but the market is clearly moving towards water based.

Our advice: for most window frames, inside and out, a good water based paint is the logical choice. Only on heavily exposed areas, or if you’re used to the way alkyd flows, is solvent based still a fine option outside.

Worth knowing: you can put water based paint straight over an old alkyd coat, and the other way round works too. Sanding properly for adhesion does matter in that case.

Preparing the surface: step by step

Expect the preparation to be the bulk of the job. A crisp finish starts here.

1. Clean and degrease the frame. Wash the timber with a degreaser or a solution of sugar soap. Grease, build up and dirt stop paint from bonding. Rinse off and let it dry.

2. Remove loose paint. Scrape flaking and lifting paint away with a paint scraper. If there’s a lot of old paint in several layers coming away, you can use a heat gun or chemical stripper. Sound, smooth paint can stay put.

3. Sand everything matt. Sand rough and weathered timber with 120 grit, and the rest of the surface with 180 to 220 grit. That kills the sheen and gives the new coat something to grip. Always sand with the grain, never across it.

4. Fill holes and damage. Fill holes, nail holes and small chips with filler or wood filler. Don’t lay it on too thick, because timber moves and a thick layer of filler will let go later. Let it dry and sand it flush.

5. Prime the bare timber. This is crucial and it’s the step people skip most. Every patch of bare wood, every repair and every badly weathered area has to be primed first. Primer soaks into the timber, fills the pores and keeps your topcoat sitting on the surface instead of sinking into the wood. Without primer on bare timber you’ll never get a durable result.

6. Wipe off the dust. After sanding, wipe away all the dust with a slightly damp cloth or a tack cloth. Dust under your paint gives a gritty, uneven finish.

7. Mask the glass and ironmongery. Mask the edge of the glass, the hinges, catches and handles with masking tape. Cover the wall below. That saves you hours of fiddling afterwards.

One important point about sealant beads: use paintable acrylic sealant, never silicone. Silicone can’t be painted over, paint simply won’t stick to it. And don’t blindly seal up every gap. A gap between masonry and timber can be a necessary escape route for moisture. Seal that and the moisture stays trapped in the wood, and your paint will flake anyway.

Building up the coats: how to apply the paint

Now for the painting itself. The golden rule: two or three thin coats beat one thick one. Thick coats sag, give runs and don’t dry through properly.

Step 1: Apply the primer. If you’ve primed bare timber, let the primer dry thoroughly as stated on the tin.

Step 2: Lightly sand the primer. Go over the dried primer very lightly with fine sandpaper (320 to 400) to take out any imperfections. Dust off again.

Step 3: Apply the first topcoat. Start at the corners and the edges along the glass, then paint the long sections. Lay the paint off in the direction of the grain. Work wet on wet: make sure the edge of the section you’ve just painted hasn’t skinned over before you start the next bit. That’s how you avoid visible lap marks.

Step 4: Sand lightly again and apply the second coat. Once the first topcoat is dry, sand it lightly again with 320 to 400 grit, wipe off the dust, then lay on your second coat. Two full coats is the minimum for a good result.

Tips for a crisp finish:

  • Dip your brush only a third of the way in and wipe off the excess on the edge of the tin
  • Work from the top down so you catch any drips as you go
  • Check regularly for runs and brush them out straight away while the paint is still wet
  • Pull the masking tape off carefully while the paint is still slightly supple, at an angle away from the paint edge, so the film doesn’t tear with it

How long should paint dry between coats?

Drying times depend on the type of paint, the temperature and the film thickness. Always go by the tin, but these are the rough rules of thumb.

Type of paint Touch dry Recoatable
Water based paint (acrylic) About 1 hour After 4 to 6 hours
Alkyd paint (solvent) Longer Usually after 16 to 24 hours

Mind the difference between “touch dry” and “fully cured”. Water based paint feels dry quickly, but it still needs days or even weeks after that to harden right through and reach full strength. Treat your frames gently during that time: no sanding, no knocks, no tape on fresh areas, and leave the sealant until the film is genuinely hard.

In cold or damp weather all the drying times stretch considerably. Allow yourself wider margins than the tin suggests.

The most common mistakes when painting window frames

Most failures come down to a handful of recurring mistakes. Avoid these and you’re most of the way there:

  • Painting in full sun or high heat. The paint dries too fast, which leaves brush marks, wrinkling and visible lap marks. Follow the shade around the house.
  • Not priming bare timber. Without primer your topcoat sinks in and lets go within a couple of seasons. Always prime every bare patch.
  • Not degreasing. A quick wash isn’t enough. Grease and build up need to come off with a proper degreaser, or nothing will bond.
  • Painting damp timber. Moisture in the wood looks for a way out through your paint film and pushes the paint off the timber. Make sure the wood is bone dry.
  • Painting over rot. Affected timber carries on rotting under the paint. Repair first, then paint.
  • Not sanding between coats. Without a light sand the next coat bonds poorly. A quick pass with fine paper takes minutes and makes all the difference.
  • Laying it on too thick. Thick coats sag, give runs and dry badly. Better thin, and twice.
  • Filling too thick. A thick layer of filler can’t cope with the timber moving and will let go. Fill only what needs filling.
  • Not masking ironmongery and glass. Hinges, handles and glass edges under the paint look scruffy and are a pain to clean up.
  • Using silicone sealant. It can’t be painted over. Use paintable acrylic sealant.

uPVC, aluminium or galvanised: can you paint those?

Yes, but the preparation is different. uPVC frames, aluminium and galvanised metal are smooth and non porous, so ordinary primer won’t bond to them.

For these materials you need a special adhesion primer, made to grip smooth surfaces. Clean and degrease the surface thoroughly first, sand it very lightly to break the sheen, apply the adhesion primer and then your topcoat over it. Without that adhesion primer the paint will flake, guaranteed.

Just want your uPVC frames looking fresh again without changing the colour? Then a thorough clean with a dedicated uPVC cleaner is often enough and you don’t need to paint at all.

What does painting window frames cost?

Doing it yourself mainly saves on labour, which is by far the biggest item on a decorator’s bill. Of the total, roughly 65 per cent is labour, around 20 per cent is materials and paint, and the rest is call out charges, sundries and VAT.

Do it yourself and you’re mainly paying for paint and tools. Reckon on about 20 to 40 euros per litre for a good quality topcoat, plus primer, brushes, sandpaper, filler, sealant and tape. For an average house that puts you somewhere between a few tens of euros and comfortably over a hundred in materials, depending on how many frames you tackle.

Have it done for you and these are roughly the going rates:

Situation Guide price
Painting interior frames €25 to €50 per m²
Painting exterior frames €35 to €60 per m²
Per frame, inside €40 to €75
Per frame, outside €50 to €150
Decorator’s hourly rate €34 to €100 per hour

The wide spread comes down to the state of the timber. Weathered frames with plenty of loose paint, rot, or awkward spots at height cost a lot more in preparation. For hard to reach work at height or large areas, a professional with the right scaffolding or ladder is often the safer and quicker option.

Checklist: painting window frames in brief

Everything in one list so you don’t forget anything:

  1. Pick dry weather, 10 to 20 degrees, not in full sun
  2. Clean the frame and degrease it
  3. Remove loose paint and sand everything matt (120 to 220 grit)
  4. Repair any rot and fill the holes
  5. Prime all the bare timber
  6. Wipe off the sanding dust and mask the glass and ironmongery
  7. Apply the first topcoat, working with the grain
  8. Sand lightly with 320 to 400 grit and dust off
  9. Apply the second coat, wet on wet, not too thick
  10. Pull the tape off in good time and let everything cure properly

Frequently asked questions

What temperature is best for painting outside?
Between 10 and 20 degrees is ideal, with around 18 degrees as the optimum. Below 5 degrees don’t start, and above 25 degrees you’re better off waiting. Keep humidity below 85 per cent and make sure the surface is at least 3 degrees above the dew point. Never paint in full sun or just before rain.

Do I always have to prime bare timber?
Yes. Bare wood, repaired areas and badly weathered sections always need priming first. The primer soaks into the timber and keeps your topcoat bonded instead of letting it sink in. Skipping this is the single biggest reason paint starts to flake.

How often should I repaint my window frames?
Good exterior paintwork lasts five to eight years, and with top quality paint sometimes up to ten. Indoors it holds for seven to ten years. A translucent stain needs more frequent maintenance than opaque paint. Repaint as soon as the sheen goes or the film starts to crack, so before the timber is left bare.

Water based or alkyd paint, which is better for window frames?
For most window frames a good water based acrylic is the logical choice: it dries fast, barely smells, hardly yellows and is kinder to the environment. Solvent based alkyd penetrates deeper into the timber and gives a hard film, but it smells, dries slowly and yellows. In the Netherlands, professionals have only been allowed to use water based paint indoors since 2000.

How long should paint dry between two coats?
Water based paint is usually touch dry after about an hour and recoatable after 4 to 6 hours. Alkyd paint generally needs 16 to 24 hours before you can apply the next coat. In cold or damp weather it takes longer. Always go by the label on your tin.

Can I paint uPVC window frames?
Yes, as long as you use a special adhesion primer. uPVC is smooth, so ordinary primer won’t bond to it. Clean and degrease the surface, sand it lightly, apply the adhesion primer and then your topcoat over it. If you just want a fresher look without changing colour, a thorough clean is often all it takes.


Fancy pushing on with the rest of the painting and finishing jobs around the house? In Koning van je Woning we show you step by step how to paint, decorate and finish to a crisp standard, exactly the way Fred would go about it: straightforward, hands on and no nonsense. Grab your brush and turn those window frames into a job you’re proud of.

Related articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Categories

.

Fred’s DIY Plans