The short answer first: you replace silicone sealant by cutting out the old bead completely, cleaning and degreasing the joint thoroughly, letting everything dry properly, masking it off with tape and then running in an even bead of fresh sanitary silicone. You tool that smooth within ten minutes, pull the tape off straight away, and leave the sealant to cure for at least 24 hours before any water touches it.
Sounds simple, and it is. The difference between a crisp bead that stays mould free for years and a grey, peeling edge is all in the preparation. Almost every failed sealant joint comes back to grease or moisture on the surface, or to the wrong sealant.
Below you will find when your sealant is due for replacement, which sealant belongs where, the full method, the curing times, the costs and the mistakes most people make.
When should you replace silicone sealant?
Silicone sealant is a consumable. It does not last forever, because it sits permanently in the dampest, warmest corner of your house.
Reckon on a lifespan of roughly 5 to 10 years. In a heavily used shower with poor ventilation it can be shorter.
Replace your sealant as soon as you see one of these signs:
- Black mould spots that no amount of cleaning will shift. The mould is in the sealant itself by then, not sitting on top of it.
- Lifting edges. The sealant is coming away from the tile or the bath. As soon as a gap opens up, water runs in behind it.
- Cracks or small holes in the bead.
- Discolouration to grey, yellow or brown that will not scrub out.
- A musty, damp smell or damp patches in the room below or next door.
That last one is the reason not to leave it too long. A failed bead around a bath or shower lets water through into the structure underneath. Insurers point out for good reason that neglected sealant maintenance can lead to serious water damage, and that damage often falls outside your cover if the maintenance has demonstrably been left undone.
In short: a tube of sealant costing a few euros prevents a repair costing hundreds or thousands.
Which sealant do you use where?
This is the bit where a lot of DIYers already go wrong, before the sealant gun even comes out. Not every sealant suits a wet joint that moves.
Sanitary silicone is the standard
For everything around the bath, shower tray, basin, worktop and tiled corners you use sanitary silicone sealant. It is:
- Waterproof, and stays that way.
- Permanently flexible, so it moves with the joint when you step into the bath or fill it with water.
- Mould resistant, thanks to added fungicides that slow mould growth down.
Silicone bonds to ceramic, glass, enamelled steel and most plastics.
Acrylic sealant does not belong here
Acrylic sealant (also sold as decorator’s caulk) is meant for dry indoor joints that barely move, along skirting boards or door frames for instance, and you can paint over it.
Never use acrylic in the bathroom on wet or flexible joints. It is not permanently water resistant and not flexible enough, so it cracks, lets water through and discolours. If the tube says “paintable”, it is almost certainly acrylic and not suitable for your bath or shower.
Acetoxy or neutral cure? The most important choice
Silicone sealant comes in two flavours, and the difference is in how it cures.
| Type | Bonds well to | Do NOT use on |
|---|---|---|
| Acetoxy silicone (smells of vinegar) | Ceramic tiles, glass, enamel | Natural stone, mirrors, bare metal |
| Neutral cure silicone (barely any smell) | Practically everything, including sensitive materials | (the safe choice almost anywhere) |
Acetoxy sealant bonds superbly to smooth, hard materials like ceramic and glass, and it cures a bit faster. But the acetic acid released while it cures is aggressive:
- On natural stone (marble, granite, bluestone) the acid soaks into the stone and causes permanent greasy or dark edges beside the joint. You will never get those out.
- On mirrors it attacks the silvering along the edge, which gives you black speckles.
- On bare metal such as aluminium or copper it causes corrosion.
The rule of thumb: if in doubt, reach for neutral cure. It is low odour, it does not attack sensitive materials, and for natural stone, mirrors, plastic shower trays and metal trims it is not even optional. The only downside is a slightly longer curing time.
What do you need?
You do not need to buy expensive kit. This is the full list:
- Sealant gun. A basic one costs a few euros, but a gun with a decent thrust ratio makes the job a lot more comfortable.
- Sealant remover tool or a sharp knife to cut the old bead free. A sharp blade is your most important tool.
- Silicone remover gel (such as Zwaluw Sili-Kill) for stubborn residue you cannot shift.
- Paint scraper or filling knife to scrape the remains away.
- Degreaser: methylated spirit or a dedicated sealant cleaner. White vinegar works too, but then rinse and dry properly afterwards.
- Masking tape for crisp lines.
- Sealant profiling tool, or just your finger with a drop of washing-up liquid in some water.
- Sealant wipes or kitchen roll to wipe off the excess.
- Mould remover if there are still mould spots on the surface.
- The right tube of sanitary silicone in the colour you want (usually white, clear or grey).
Method: replacing silicone sealant in 7 steps
Take your time. Removing and cleaning takes longer than the sealing itself, but it is what decides the result.
1. Remove the old sealant completely
Cut along both sides of the bead with a sharp knife. Then cut the sealant free in strips and pull them out.
All the old sealant has to go. Fresh silicone does not bond to old silicone.
If you cannot get the residue off, apply silicone remover gel, let it work according to the instructions on the packaging and then scrape the remains away with a filling knife or paint scraper.
2. Treat any mould and check the joint
Are there still black mould spots on the surface? Treat them with mould remover and let the product work. Fresh sealant over mould that was left behind will simply go mouldy again.
Check the surrounding tile grout while you are at it. If that has failed, repair it first.
3. Clean and degrease thoroughly
This is the most important step. Grease, soap residue and leftover cleaning product are the number one reason fresh sealant does not bond.
Clean the joint out and then degrease with methylated spirit or a sealant cleaner. Wipe over with a clean cloth.
4. Let the joint dry completely
Silicone does not bond to a damp surface. After cleaning, let the joint dry out properly. If you have been working with water or vinegar, happily give it an hour.
Tip: seal at a moment when nobody needs to shower for a while afterwards, so everything stays dry.
5. Mask off for crisp lines
Run masking tape along both sides of the joint, leaving a gap of about 2 to 3 mm between the two strips for the sealant. That gives you a dead straight, even bead, even if you have never sealed anything in your life.
6. Apply the sealant
Cut the nozzle of the tube off at an angle. The lower down you cut, the wider the opening and the thicker your bead. Cut the opening slightly narrower than the width of your joint.
Put the tube in the gun, pierce the foil seal inside and screw the nozzle on.
Now squeeze a full bead of sealant into the joint in one even, continuous movement. Make sure there is enough sealant in the joint so no voids are left behind.
7. Tool it smooth and pull the tape off immediately
Smooth the sealant within a couple of minutes using a wet finger (a drop of washing-up liquid in water) or a profiling tool. Do it in one flowing pass.
Then pull the masking tape off immediately, while the sealant is still wet. Leave it too long and you tear the edge of your fresh bead apart.
Work quickly: a neutral cure sanitary sealant skins over after about 10 minutes. Once that skin has formed, keep your hands off the joint.
How long does sealant take to dry and cure?
This is where it often goes wrong: people think the sealant is finished as soon as it feels dry. It is not.
There are two moments:
- Skin formation: after roughly 10 minutes. The outside has dried off by then. That is your deadline for tooling.
- Fully cured: this takes far longer. Silicone cures from the outside in at a rate of about 2 mm per 24 hours (Soudal Silirub 2S, for example). So a joint 5 to 6 mm deep is only cured all the way through after a few days.
The practical rule of thumb: keep the joint dry for at least 24 hours. So no showering, no filling the bath, no washing-up water along the worktop joint. With a thick bead or poor ventilation, feel free to leave it alone for 48 hours.
Patience pays off here. Water on half cured sealant means a poor bond, and often peeling edges or mould again in no time.
Common mistakes when resealing
Most problems are avoidable. These are the classics:
- Fresh sealant over old or dirty sealant. Silicone does not bond to silicone. It all has to come off.
- Not degreasing. Grease and soap residue stop it bonding. Always degrease and let it dry.
- Acetoxy sealant on natural stone or mirrors. Permanent staining and a damaged mirror edge. Use neutral cure here.
- Water too soon. The sealant is dry on the outside but not cured through. Wait 24 hours.
- Using acrylic in wet areas. It is not water resistant and it cracks.
- A bead that is too thick or uneven. Cut the nozzle to size, work in one movement and tool in one pass.
- Removing the tape too late. Pull the tape off while the sealant is still wet.
Preventing mould after sealing
Fresh sealant is mould resistant, but it is not a miracle cure. You feed mould with moisture, so keep things dry:
- Ventilate properly. Open a window or run the extractor during and after showering.
- Dry the joint off after showering with a squeegee or a cloth, certainly in a poorly ventilated room.
- When you reseal, always choose a mould resistant sanitary silicone.
Do that and you will get the full 5 to 10 years out of your bead.
What does replacing silicone sealant cost?
Doing it yourself is dirt cheap compared with paying someone. The prices below are guide figures (2026) and can vary from shop to shop.
Doing it yourself, materials:
| Item | Guide price |
|---|---|
| Tube of sanitary silicone | 5 to 12 euros |
| Sealant gun | 5 to 20 euros |
| Silicone remover gel | 4 to 8 euros |
| Masking tape, blade, wipes | a few euros |
For an average bathroom you will be done with one or two tubes. Reckon on roughly 20 to 40 euros in materials if you buy everything new, and less if you already have a sealant gun lying about.
Paying a sealant specialist or plumber:
- Applying sealant costs on average 4 to 11 euros per linear metre.
- Including removal of the old bead, that sits around 6 to 11 euros per metre.
- Many tradespeople charge a call-out or minimum fee (often 100 to 200 euros) for small jobs.
- Having a complete bathroom resealed soon adds up to 150 to 450 euros including VAT.
The sums are clear: with half a day’s work and 20 to 40 euros of materials you save a hundred euros or more without much effort. And you pick up a skill you can use again every 5 to 10 years.
Frequently asked questions
Can I apply fresh sealant over old sealant?
No. Fresh silicone does not bond to old silicone. You have to remove the old bead completely, clean and degrease the joint, and only then reseal. Sealant over old sealant is guaranteed to come away.
How long does silicone need to dry before I can shower?
Wait at least 24 hours before letting water touch the fresh sealant. It feels dry after a few hours, but it cures from the outside in at about 2 mm per day. With a thick bead or a damp room you are better off allowing 48 hours.
Which sealant do I use for natural stone?
Always neutral cure silicone. On natural stone such as marble or granite, acetoxy sealant causes permanent greasy and dark edges that you will never get out. Neutral cure sealant is low odour and safe for sensitive materials.
Why does my sealant keep peeling off or going mouldy?
Almost always because of a dirty or damp surface. Grease, soap residue and leftover moisture stop the sealant bonding. Remove all the old sealant, treat any mould, degrease thoroughly and let the joint dry completely before you reseal.
How often should you replace silicone sealant?
Reckon on every 5 to 10 years, or sooner as soon as you see mould that will not scrub out, lifting edges, cracks or discolouration. Do not leave it too long, because a leaking bead can cause water damage.
Which is better: acetoxy or neutral cure silicone?
Acetoxy bonds slightly better to ceramic and glass and cures faster, but it attacks natural stone, mirrors and metal. Neutral cure is the safe choice for almost every job and is a must on natural stone, mirrors and plastics. If in doubt, go neutral.
Want to take on more jobs like this around the house? At Fred’s DIY Plans I show you step by step how to tackle bathrooms, kitchens, walls and floors yourself, with the order of work, the sizes and the materials the pros use. Have a look here.
Best regards from Fred Schouten, builder and DIYer through and through
PS: pencil the date on the back of the access panel or inside the bathroom cabinet when you are finished. In six years you will be standing in front of that bead wondering whether it is five years old or twelve. Small tip. Big difference.


