You build a retaining wall in four layers: a solid, frost-free foundation, a wall that leans slightly backwards, a zone of drainage gravel with geotextile behind it, and an outlet for the water that ends up in there. Up to roughly 50 cm of retained height you can handle this yourself, either with boards on posts or with dry-stacked concrete blocks. Between 50 cm and 1 metre it is still a DIY job, but then everything has to be right. Above 1 metre of level difference you will normally need permission from the local authority, and you want a structural engineer or a landscaper involved.
And now the most important sentence in this whole article: when a retaining wall fails, water is almost always the cause. Not the soil, not the weight, not boards that are too thin. Water sitting behind the wall with nowhere to go.
That is exactly why you know that one neighbour with the crooked garden wall that started bulging after two winters. There was no drainage behind it. Below you will read how to do it properly: which systems exist and up to what height they work, how much force really lands on your wall, how to build the foundation and the drainage, what it costs and which rules apply.
What is actually pushing against that wall?
This little calculation makes it clear in one go why a 40 cm retaining wall is child’s play and a 1.5 metre one is serious work.
The soil behind a wall pushes with a force that increases with the square of the height. Double the height and the pressure quadruples. For normal sandy soil it looks roughly like this, per linear metre of wall:
| Retained height | Force per linear metre (dry sandy soil) | Comparison |
|---|---|---|
| 0.3 m | About 27 kg | A bag of sand |
| 0.5 m | About 75 kg | An adult |
| 1.0 m | About 300 kg | A decent-sized motorbike |
| 1.5 m | About 675 kg | A small car |
| 2.0 m | About 1,200 kg | A pick-up truck |
(Calculated with the standard formula for active earth pressure: 0.5 x Ka x unit weight x height², with Ka = 0.33 for sand and a unit weight of 18 kN/m³.)
So at 30 cm there is literally a bag of sand hanging off your wall. At 1.5 metres, a car. Per metre. That is why a 40 cm retaining wall made of four boards and a few posts stands for years, and why exactly the same construction at 1.2 metres starts bulging within two years.
And then the water joins in. If the soil behind your wall fills up with rainwater and it cannot escape, the water pressure comes on top of everything else. With fully saturated soil the total load on your wall roughly doubles. Water is the quiet destroyer, and it is precisely the factor you can switch off with a cheap zone of gravel and a piece of geotextile.
The three ways a retaining wall fails
Understand these three and you understand every design choice in this article.
1. Overturning. The wall rotates forwards about its base. You spot it as a wall that bulges at the top while the foot still sits neatly in place. Solution: mass at the back (an L-shaped unit with a heel the soil presses down on), or lean the wall backwards, or tie it back with an anchor.
2. Sliding. The whole wall slides forwards as one over its foundation. Recognisable by a gap opening up behind the wall. Solution: a wider footing, a rough or deeper foundation, and posts that go deep enough.
3. Washing out and settling. Soil washes away between or under the wall, or the foundation sinks unevenly into soft ground. Recognisable by a wavy top edge and by soil piling up on the low side. Solution: geotextile, a well-compacted foundation layer and backfilling in layers.
Almost every problem with a DIY retaining wall traces back to one of these three, and in almost every case water was the trigger.
Which system suits which height?
This is the decision that determines everything. Here is an honest comparison, including the heights at which you can still responsibly do the work yourself.
| System | DIY up to | Material cost per linear metre (indicative) | Strong point | Weak point |
|---|---|---|---|---|
| Graded bank (no wall, just a slope) | Any height | Almost nothing, just planting | Cheapest, natural, no structure that can fail | Eats up garden space: 2 to 3 m of width per metre of height |
| Sheet piling boards on posts (hardwood) | Around 60-80 cm | Roughly 40-120 euros | Quick to install, warm, doable by hand | Timber has a finite life, even hardwood |
| Plastic or composite sheet piling boards | Around 50-60 cm | Roughly 40-100 euros | Does not rot, lightweight | Less stiff, starts flexing on taller walls |
| Stackable blocks (dry-stacked concrete blocks) | Around 80-100 cm | Roughly 60-150 euros | Modular, good-looking, no crane needed | Demands a perfect, wide foundation layer |
| Gabions (stone-filled baskets) | Around 100 cm | Roughly 60-150 euros | Free-draining by nature, robust, simple | Heavy filling work, filling them takes a full day |
| Masonry wall (brick or block) | Around 50 cm without an engineer | Roughly 80-200 euros | Suits an existing masonry garden | Needs a proper foundation and reinforcement, cracks quickly on settlement |
| Precast L-shaped concrete units | Barely: crane needed | On request, plus transport and crane | Strongest solution, also for 1.5 m and above | A 2.5 m unit weighs nearly 1,900 kg |
| Steel retaining wall or sheet pile section | Limited | Varies widely | Slim, strong, takes up little space | Vibrating or pressing it in calls for plant |
(Sources: hovenier.nl, tuinafscheiding.nl, sorfan.de)
Prices vary hugely by timber species, block size and supplier. Always get a current quote for your exact dimensions and add the foundation, the gravel and the geotextile on top.
The option everyone forgets: simply not retaining at all
Before you dive into a system: a graded bank is almost always the cheapest and most durable solution. A slope of 1 in 2 (2 metres horizontally for every metre of height) stays put on its own in most soil types, certainly with planting on it. On sandy soil you are better off with 1 in 3.
The downside is obvious: you lose garden space. But if you have that space, you save yourself the structure, the drainage, the maintenance and the risk. Plant the bank with ground cover that holds the soil with its roots: cotoneaster, climbing hydrangea, hardy geranium, or simply perennials with a strong root system. Get it planted straight away in any case, because bare soil on a slope washes downhill in the first heavy downpour.
And the option that works best over a big level difference: terracing
Need to bridge 1.5 metres? Then consider two 70 cm retaining walls with a metre-and-a-half strip in between, instead of a single 1.5 metre one. The force per wall then drops from about 675 kg per linear metre to about 150 kg per metre. That is almost a factor of five less, and it moves the project from “needs an engineer” to “I can do this myself”.
Bonus: that middle strip is instantly a planting border or a path. Terracing is not a compromise, it is often the best solution.
Permission and the rules
The rule of thumb used in the Netherlands, where the sources for this article come from: up to 1 metre of level difference, a retaining wall or quay wall needs no permission. If the difference between the two levels is more than 1 metre, you have to apply for it. (Source: vergunningsvrijbouwen.com) Thresholds and conditions differ from country to country and often from council to council, so check with your local planning department. The order of magnitude, that things get serious from about a metre, is a good starting point for that conversation.
Two additions that often go wrong:
- Measuring in water. If the retaining wall stands in water (along a ditch or pond), you measure from the bed of that watercourse to the top of the wall. So that is often a lot more than the visible height.
- Not sticking up above the higher ground. The retaining wall must not rise above ground level of the highest part of the plot. If it does, that top section is effectively a boundary fence, and different rules apply to that.
On top of that:
- Alongside a ditch, canal or watercourse the water authority almost always has its own regulations. There you usually need a permit or at least a notification, even under 1 metre. Give them a call.
- Your local development plan may set extra rules, certainly in a conservation area or around listed buildings. One phone call to the council is quickly done.
Boundary law: almost everyone underestimates this
If you dig out or build up near the boundary, that affects your neighbours. A few things worth knowing:
- You are allowed to dig away soil on your own plot, but you are responsible for the consequences. Dig in a way that makes your neighbour’s ground crumble away or settle and that is your problem, not theirs.
- The retaining wall you build to make that excavation work is a structure you own. That makes you liable for consequential damage if the wall fails. (Source: rechtswinkel.nl)
- Water that runs onto the neighbours because of your build-up is your responsibility too. So think about where your drainage discharges: it must not simply dump over the boundary.
Practical tip: pop round to the neighbours before you start, show them what you are planning and put the agreement down briefly in writing, even if it is just a message with a photo of the drawing. It costs you five minutes and in the worst case saves you a solicitor.
Step by step: a retaining wall of sheet piling boards on posts
This is the most commonly built DIY version, up to around 60 to 80 cm of retained height.
Step 1: setting out and measuring
Run a taut line along the whole route, level or with a set fall. Measure the actual level difference at several points: gardens are rarely evenly sloped. Decide where your top edge goes and how deep you need to dig out or build up.
Think about the outlet now, not later: where is the water from your drainage going to go? To a chamber, a gravel soakaway, the ditch or your rainwater drain? That determines the fall on your drainage pipe, and that in turn determines the level of your foundation.
Step 2: the posts
The rule of thumb for timber retaining wall posts: the post is about three times the retained height, and two thirds of it sits in the ground. (Source: tuinafscheiding.nl)
| Retained height | Post length | Depth in the ground |
|---|---|---|
| 30 cm | 90 cm | 60 cm |
| 50 cm | 150 cm | 100 cm |
| 70 cm | 210 cm | 140 cm |
| 100 cm | 300 cm | 200 cm |
Look at that last row and you understand why a 1 metre retaining wall with timber posts is such hard graft: you have to go 2 metres into the ground. That is why above roughly 70 cm you are usually better off with a different system.
Use hardwood posts of at least 8.8 x 8.8 cm, heavier as the height goes up. Set them at around 40 to 60 cm centres on tall walls, and up to around 100 cm for a low 30 cm retainer. Bore the holes with a post hole auger: it is faster than digging and the surrounding soil stays firm.
Set the posts leaning back by 5 degrees, so with the top tilted slightly into the slope. (Source: tuinafscheiding.nl) Soil always settles a little, and a wall that starts out perfectly vertical is visibly leaning forward after two years. A wall that starts out leaning back is still standing straight by then. In the trade this is called the batter, and it is the difference between a wall that looks crisp and one your eye keeps snagging on.
There are two ways to fix the posts: tamped into clean sand with gravel (free-draining, and you can correct things later), or set in concrete (more rigid, but it rots the timber faster if water sits in the concrete collar). If you do concrete them, dome the top of the collar so water runs off.
Step 3: the boards
Fix the sheet piling boards to the soil side of the posts, not to the front. That sounds counterintuitive but it is essential: now the soil presses the boards against the posts instead of off them. Your fixings then only have to hold the board in place, not carry the entire soil pressure.
Use stainless steel or hot-dip galvanised bolts with a washer, not screws. A screw in a retaining wall will pull itself out over time, a through bolt will not. Allow at least two fixings per board per post.
Sheet piling boards interlock with a tongue-and-groove joint, so you stack them from the bottom up. Start with the bottom board genuinely at or slightly below ground level on the low side, so nothing can wash out underneath.
Finish the top with a capping board over the heads of the posts. That is not just tidier, it protects the end grain from rain, and end grain is exactly where timber starts to rot.
Step 4: geotextile and the drainage zone
Now comes the part most DIYers skip, and precisely why their wall fails.
- Line the back of the wall with geotextile (weed membrane is not the same thing: get proper filter fabric or drainage geotextile). Let the fabric run well past the edges: across the bottom of the trench and later over the top of your gravel zone, like a folded-over envelope.
- Lay a drainage pipe (usually 80 to 100 mm, corrugated and sleeved) on the bottom, directly behind the wall, with a slight fall towards the point where the water is allowed to go. At least 1 cm of fall per metre.
- Fill a zone of drainage gravel behind the wall: at least 20 to 30 cm wide over the full height, from the bottom up to about 15 cm below ground level. Use washed gravel 8-16 or 16-32 mm, not unwashed crushed hardcore: that silts up.
- Fold the geotextile closed over the top of the gravel zone and top up the last 15 cm with soil. Without that closing layer of fabric, fine silt washes into the gravel and in three years your drainage is one solid block of silted-up sand.
Why this works: gravel has far more void space than soil, so water sinks straight through it and is carried off by the pipe. The water pressure behind your wall then never builds up in the first place. The geotextile keeps the gravel clean so it goes on working.
Where do you put the water? A gravel soakaway or a soakaway crate in the low part of the garden is usually the simplest option. Connecting to your rainwater drain is often allowed, but check first. Discharging over the boundary or straight into a ditch: have a quick word with the council or the water authority first.
Step 5: backfilling in layers
Backfill the soil behind the wall in layers of 20 to 30 cm, and compact every layer separately with a wacker plate or a hand tamper. Skip that and tip in a barrowload of soil in one go, and that soil will settle over the next two years, leaving you a dip right behind your brand new wall.
Do compact carefully though: a heavy wacker plate right behind a freshly built wall can push it forwards. Keep the last 50 cm behind the wall to hand tools only.
For the top layer: use slightly clayey, less permeable soil rather than sand. That layer acts as a lid that sheds rainwater across the surface instead of letting it run into your gravel zone. Get planting on it straight away.
Step by step: a retaining wall of stackable blocks
The best-looking DIY option up to around 80 to 100 cm, and also the least forgiving. Everything here hangs on the foundation.
Step 1: the foundation trench
Dig a trench at least twice as wide as your block and about 15 to 25 cm deep below the final ground level of the low side. Fill it with crushed hardcore or MOT type sub-base, in 10 cm layers, and compact each layer with a wacker plate.
Be generous here: a wall of stackable blocks is a dry stack without mortar, so every millimetre of unevenness in the bottom course multiplies as you go up. Make the top layer of your foundation bed from fine grit or sharp sand and screed it perfectly flat with a straight edge.
Step 2: the first course, and only the first course
Take your time here. Lay every block level in two directions and check the top with a long straight edge and a spirit level. A 3 mm difference in the first course becomes a visibly crooked wall by the tenth.
Preferably set the first course entirely below ground level, so the soil at the front holds the wall back as well. That is free stability.
Step 3: stacking with a stagger
Stack the blocks in a stretcher bond, so every course shifted by half a block relative to the one below. Many system blocks have a lip or a pin on the back that automatically sets each course a couple of centimetres further back. That backwards lean (roughly 1 in 10, so 10 cm back per metre of height) is exactly what keeps the wall stable.
Got plain blocks with no lip? Then set each course back by about 1 cm yourself and use exterior construction adhesive between the courses.
Step 4: drainage, geotextile, backfilling
Exactly as with the timber wall above: geotextile, drainage pipe laid to a fall, a gravel zone of at least 20 to 30 cm, fabric folded closed, backfilled in layers of 20 to 30 cm.
With stackable blocks the drainage zone matters even more than with timber, because a dry stack has no tensile strength whatsoever. Water pressure simply shoves it forward course by course.
Step 5: the capping course
Glue the top course down with construction adhesive or use dedicated capping blocks. Otherwise that is the course children push off and the one that ends up on the ground after the first hard frost.
When do you bring someone in?
Be honest with yourself here. Call a landscaper, a builder or a structural engineer if:
- The level difference is more than 1 metre. Then you need permission anyway.
- The retaining wall has to hold back soil with something on it: a shed, a patio people walk on, a drive a car parks on. A surcharge load changes the sums completely.
- The ground is soft: peat, wet clay, hydraulically filled sand. Any foundation will sink there unless you adapt it.
- There is an existing wall, fence or building behind it within roughly the height of your wall.
- You are working near a ditch, embankment or watercourse.
- The wall goes on or right along the boundary.
Costs for having one built vary widely: for a simple board wall reckon on roughly 100 to 300 euros per square metre of visible wall face, labour included, and considerably more once a crane, concrete work or L-shaped units are involved. (Source: grondverzet.nu)
What does it cost if you do it yourself?
For a retaining wall 10 metres long and 50 cm high, in sheet piling boards on hardwood posts:
| Item | Indication |
|---|---|
| Hardwood posts 8.8 x 8.8 cm, 150 cm long, around 15 of them | 200-450 euros |
| Hardwood sheet piling boards, around 5 m² | 200-600 euros |
| Stainless or galvanised bolts, washers and nuts | 40-90 euros |
| Geotextile (roll) | 30-70 euros |
| Drainage pipe 80 mm, sleeved, 12 m | 30-60 euros |
| Drainage gravel, around 1.5 m³ | 90-180 euros |
| Post hole auger hire (half day) | 30-70 euros |
| Wacker plate hire (day) | 50-90 euros |
| Outlet or soakaway crate | 50-150 euros |
That comes to roughly 700 to 1,700 euros in materials and hire, plus two to three solid days of work. Go for stackable blocks and the materials land in the same range, but you get more foundation work and more hauling.
The biggest hidden cost is almost always getting rid of the spoil. Dig out a corner of your garden and those cubic metres of soil have to go somewhere. A cubic metre of soil weighs roughly 1,500 to 1,800 kg, and a skip for soil soon runs to a few hundred euros. So first see whether you can use the soil elsewhere in the garden: as build-up, as raised bed height, or as a base under a path.
The ten mistakes you want to avoid
- No drainage. The main cause of virtually every failed retaining wall. A zone of gravel with geotextile costs you 150 euros and saves the whole project.
- Unwashed hardcore as drainage gravel. It silts up within a few years. Get washed gravel.
- Not folding the geotextile closed at the top. Fine silt then washes into your gravel zone from above.
- Boards on the wrong side of the posts. Fix them on the soil side, then the soil presses them against the post.
- Screws instead of bolts. Screws pull themselves out under tension.
- Setting the wall bolt upright. Lean it back 5 degrees and it is still standing straight in three years.
- Posts too shallow. Two thirds of the post length in the ground, minimum.
- Backfilling in one go without compacting. You are guaranteed a dip right behind the wall.
- Trying to take the whole height in one wall. Terracing with two low walls is almost always cheaper, safer and better looking.
- Skipping the permission and the neighbours. A retaining wall on the boundary is a fine way to buy yourself years of neighbour trouble.
Frequently asked questions
Up to what height can I build a retaining wall myself without permission?
As a rule of thumb: up to 1 metre of level difference a retaining wall or quay wall needs no permission, and above 1 metre you have to apply. The exact threshold varies by country and council, so check with your local planning department. If the wall stands in water, you measure from the bed of the ditch or watercourse, so the measurable height is often greater than you think. On top of that, the retaining wall must not rise above ground level of the highest part of the plot. Along a ditch or watercourse the water authority may set its own rules as well.
Do I really need drainage behind a retaining wall?
Yes. Water is the number one cause of failed retaining walls. Soil that becomes saturated with rainwater pushes roughly twice as hard against your wall as dry soil, and that pressure builds until the wall overturns or slides. A zone of washed drainage gravel 20 to 30 cm wide, a drainage pipe laid to a fall and geotextile keeping the gravel clean cost very little together and take that pressure away entirely.
How deep do the posts of a timber retaining wall need to go?
The rule of thumb: the post is three times the retained height and two thirds of it sits in the ground. So for a retained height of 50 cm you take a 150 cm post with 100 cm in the ground. At 70 cm of retained height that becomes a 210 cm post with 140 cm in the ground. Above roughly 70 cm that is so much digging that another system is usually more practical.
Which is better: a retaining wall or a graded bank?
If you have the room, a bank is nearly always cheaper, more durable and easier to maintain: there is no structure that can fail. Allow 2 to 3 metres of width per metre of level difference, and plant the bank straight away with ground cover so the soil does not wash away. If you do not have that room, a retaining wall is the answer. For bigger heights, consider terracing: two low walls instead of one tall one.
How much pressure is on a 1 metre retaining wall?
With normal dry sandy soil, roughly 300 kg per linear metre of wall. That force increases with the square of the height: at 1.5 metres it is already about 675 kg per metre and at 2 metres about 1,200 kg per metre. If the soil becomes saturated with water, that load roughly doubles. That is exactly why low walls are easy and tall walls genuinely need calculating.
Why is my retaining wall bulging forwards?
Almost always one of three things. Water sitting behind the wall and driving the pressure up, by far the most common cause. Posts that do not go deep enough, so the wall overturns as a whole. Or soil that was backfilled in one go without compaction and is still settling and pushing years later. A wall that is already visibly bulging can rarely be repaired without taking it apart: dig it out, build a proper drainage zone in after all, and rebuild it with the posts deeper or closer together.
What gravel goes behind a retaining wall?
Washed drainage gravel or grit, usually in sizes 8-16 mm or 16-32 mm. Do not use unwashed mixed hardcore or crushed rubble: it contains fine material that silts up the void space in a few years, and then your drainage has stopped working. Separate the gravel from the backfill on all sides with geotextile, including at the top.
Can I put a retaining wall on the boundary?
You can, but always discuss it with your neighbours beforehand and put the agreement in writing. As the owner of the retaining wall you are liable for damage arising from it, for example if the neighbours’ soil starts settling or if your drainage water runs their way. Above 1 metre of level difference you also need permission, and councils tend to look more closely at an earth-retaining structure on a boundary.
Sorting out a change in level in the garden is one of those jobs where a good plan up front pays off the most: the right height, the right dimensions and the drainage drawn in from the start. Want to tackle a garden project like this with a complete build plan, materials list and cutting list? Then have a look at the plans at https://www.fredsdiyplans.com/.


