You install brick slips in five steps: prepare and prime the surface, apply adhesive with a notched trowel, press the slips into the adhesive bed, cut to size where needed, and point after at least 24 hours.
Reckon on roughly 40 to 55 slips per m², about 3 to 5 kg of adhesive per m² and 3 to 5 kg of pointing mortar per m² if you work with joints.
The adhesive under the slips needs to dry for 24 hours before you point, and the whole wall is fully cured after 5 to 7 days.
In 2026, materials cost roughly 30 to 90 euros per m² (slips only), or 120 to 220 euros per m² if you have them fitted.
Indoors on plasterboard you use ready-mixed paste adhesive, outdoors on a facade you use a cement-based flexible adhesive that is frost-resistant. Below I explain every step so you never have to look anywhere else.
What exactly are brick slips?
Brick slips are thin slices of brick or natural stone, usually 10 to 25 mm thick. You glue them onto a wall so it looks like a real brick or natural stone wall, without any bricklaying.
So you keep the brick look without the weight and thickness of a real stone wall. A real half-brick wall is 100 mm thick and seriously heavy. Brick slips add only a few centimetres.
There are broadly three types:
- Fired brick slips (clay): real clay, kiln-fired. The toughest, most authentic look. A bit pricier.
- Natural stone slips: slate, quartzite, travertine. Often for a rural or rustic feel.
- Mineral or concrete slips: cast concrete with a stone look. Cheaper, lighter, easier to cut.
The difference with brick slips on panels or boards
Besides loose slips, there are also brick slip panels: ready-made boards with the slips already attached, often with a click or interlocking system.
Loose slips you glue one by one. That is more work but gives the nicest, most natural bond, and you can choose any pattern.
Panels go much faster and are ideal for large areas, but you pay more per m², and the seams between panels need attention. This guide is about gluing loose brick slips, because that is what most people do at home.
What surface can I install brick slips on?
The surface needs to be three things: flat, solid and dust-free. Adhesive does not bond to loose, greasy or powdery material.
Suitable surfaces:
| Surface | Suitable? | Watch out |
|---|---|---|
| Rendered masonry / concrete | Yes | Must be flat and load-bearing |
| Plasterboard (drywall) | Yes, indoors | Screw it well, check max weight around 30 kg/m² |
| Sand-lime brick / aerated concrete | Yes | Prime first against suction |
| Existing tiles | Sometimes | Roughen up or use a special bonding primer |
| Wallpaper | No | Remove first, always |
| Loose, chalky plaster | No | Knock off and repair first |
Important: a plasterboard wall has a weight limit. Fired brick slips can weigh 30 to 45 kg per m². Light mineral slips sit around 15 to 25 kg per m². Always check whether your wall and fixings can take it, and when in doubt choose lighter slips on plasterboard.
Preparing the surface: flat, dust-free and primed
Do not skip this step. This is where beginners go wrong most often.
- Clean it. Remove dust, grease, old paint residue and loose bits. Sweep, wipe down, and if needed go over it with a degreaser.
- Repair imperfections. Fill holes and cracks with repair mortar or filler. Brick slips do not always hide small imperfections, you will see a bump come through.
- Prime (primer). Apply a priming agent, also called a base coat or primer. This does two things: it binds dust and it slows the wall’s suction, so the adhesive does not dry out too fast and bonds well.
You use roughly 1 litre of primer per 8 to 10 m² for one coat. On strongly absorbent surfaces (aerated concrete, sand-lime brick) apply two coats.
Let the primer dry according to the packaging, usually 2 to 4 hours, before you carry on.
Trade term: “suction” is how fast a wall draws water out of the adhesive. Too much suction dries your adhesive before it bonds. Priming fixes that.
Which adhesive for brick slips? Indoors versus outdoors
This is the most important choice, and where many guides stay vague. The rule of thumb:
| Application | Adhesive type | Why |
|---|---|---|
| Indoor, dry room | Paste adhesive (ready-mixed in a tub) | Easy, no mixing, enough for indoors |
| Indoor, wet room (bathroom) | Cement-based flexible adhesive | Moisture-resistant and more flexible |
| Outdoor facade | Cement-based flexible adhesive, frost-resistant (class C2) | Must cope with frost, damp and temperature swings |
| Natural stone slips | Special natural stone adhesive | Prevents discolouration/efflorescence on some stone types |
Paste adhesive comes in a ready-mixed tub, you start straight away. Only for indoors on dry walls.
Flexible adhesive you have to mix with water (powder into a bucket, stir with a drill and paddle). The word “flex” means the adhesive absorbs small movements of the wall without cracking. Outdoors that is not a luxury but a must, a facade expands and contracts with the seasons.
For natural stone: with light stone types choose a white or pale natural stone adhesive, otherwise the dark adhesive sometimes shows through.
With joints or without joints?
Two styles, both good, but the choice decides your method and your consumption.
With joints (open bond): you leave about 10 to 12 mm of space between the slips, just like real masonry, and fill it afterwards with pointing mortar. This gives the most authentic brick look. More work, more material.
Without joints (jointless, butt-to-butt): you place the slips tight against each other, with no gap. Modern, sleek, quickly done. Many natural stone slips are made exactly for this. You skip the whole pointing step.
Rule of thumb: fired brick slips look best with joints. Sleek slate or a modern interior you often choose without joints.
Do I need corner slips?
For internal and external corners there are special corner slips: two slips joined at a 90-degree angle, or L-shaped pieces.
With these the brick look wraps neatly around the corner, without showing the ugly thin side edge of a normal slip. At a window opening, an external corner of a fireplace or a reveal they are worth the money.
Always start at the corner. Place all the corner slips first, alternate per row which side has the long leg (just like a masonry bond), and then work in the flat field.
Natural stone slips you can sometimes simply butt together in the corner without a corner slip. Fired brick always looks better with corner slips.
Tool list
Lay this out before you start:
- Priming agent + brush or roller
- Adhesive (paste or flexible adhesive, see above)
- Notched trowel (6 mm notch for small slips, 8 to 10 mm for thicker ones)
- Bucket + drill with mixing paddle (for flexible adhesive)
- Spirit level and a straight batten
- Pencil and tape measure
- Mason’s line or laser line for the height lines
- Tile cutter or angle grinder with a diamond blade
- Pointing mortar + pointing bag or piping bag (for pointing)
- Pointing iron or jointing tool
- Clean sponge and bucket of water
- Impregnating agent (outdoors or wet room only)
- Spacers or 10 mm wood offcuts (for even joints)
Step-by-step: installing brick slips in 6 steps
Step 1: Mark out your lines
Using a spirit level, draw a horizontal guide line on the wall, about half a slip height above the floor. That is where you start, so you can finish neatly at the bottom.
Stretch a mason’s line or set a laser line for the first row. A crooked first row runs through the whole wall.
Step 2: Apply the adhesive
Stir the paste adhesive briefly, or mix the flexible adhesive according to the packaging (let it slake for 5 minutes, then stir again).
Spread a layer onto the wall with the flat side of the notched trowel, no bigger than you can cover in 15 to 20 minutes. Then comb through with the toothed side, in one direction.
Tip: with larger or outdoor slips, also butter the back of the slip thinly (“buttering”). Then there is adhesive everywhere and you leave no voids behind the slip, which matters outdoors against moisture.
Step 3: Place the slips
Press each slip into the adhesive bed with a light sliding motion. This creates full contact and squeezes the air out.
Working with joints? Keep 10 mm using spacers or wood offcuts. Working without joints, press the slips tight against each other.
Check every 2 to 4 rows with the spirit level that everything runs straight. You can still adjust while the adhesive is wet.
Step 4: Cutting brick slips
Slips that are too long you cut to size with a tile cutter (wet cut, little dust) or an angle grinder with a diamond blade.
Place the cut edge as much as possible into corners or against frames, so you keep the factory edge on show. Slips break easily, take it steady.
Order 10% extra material for cutting waste and breakage. That is not excess, that is realistic.
Step 5: Let the adhesive dry
Let the adhesive dry for at least 24 hours before you point. Do not load or point the wall sooner, otherwise the slips will slide.
Step 6: Pointing (with joints only)
Mix the pointing mortar according to the packaging. Fill your pointing bag or piping bag and pipe the mortar into the joints, from top to bottom.
Let the joint stiffen up a little (finger-press test: it should no longer stick to your finger, often after 20 to 40 minutes). Then tool the joint with a pointing iron for a nice concave, sealed joint.
Brush away excess mortar with a dry brush. Be careful with wet sponges on brick, that quickly causes efflorescence (a white haze).
Coverage per m²: slips, adhesive and pointing
Concrete figures, so you do not come up short at the builders’ merchant:
| Material | Coverage per m² | Note |
|---|---|---|
| Brick slips | 40 to 55 pieces | Depends on the format; check the packaging |
| Primer | 0.1 to 0.15 litres | 1 litre covers 8 to 10 m² |
| Adhesive | 3 to 5 kg | Thicker/outdoor slips more; a 25 kg bag covers 5 to 8 m² |
| Pointing mortar | 3 to 5 kg | Only when pointing; depends on joint width |
| Extra purchase | +10% | For cutting waste and breakage |
Unsure about the number of slips? Take the number of slips the manufacturer states per m² on the packaging, that is always the most reliable.
Drying and curing times
| Stage | Time | Watch out |
|---|---|---|
| Primer dry | 2 to 4 hours | Before you start gluing |
| Adhesive workable | 15 to 20 minutes | After that the adhesive skins over |
| Adhesive dry (before pointing) | at least 24 hours | Do not point or load sooner |
| Joint stiffening | 20 to 40 min | Before you tool it |
| Fully cured | 5 to 7 days | Before impregnating or loading outdoors |
Do not work below 5 degrees and not in full sun or strong wind outdoors. Too cold means the adhesive will not cure, too warm or windy dries the adhesive before it bonds.
Indoors on plasterboard versus an outdoor facade
The steps look alike, but there are real differences.
Indoors on plasterboard:
- Use paste adhesive (dry room) or flexible adhesive (bathroom).
- Mind the weight: choose light mineral slips if the wall cannot take heavy work.
- No frost, no damp from outside, so no impregnating needed (except in a shower area).
- Priming stays sensible against dust and suction.
Outdoor facade:
- Always cement-based, frost-resistant flexible adhesive (C2). Paste adhesive will not survive the winter.
- Butter the back of the slip too, no voids behind the slip where moisture sits.
- Work dry and frost-free. Plan it for spring or late summer, not January.
- Impregnate the facade after curing (see below).
- With insulation underneath (external wall insulation) you work on a special insulation render system, that is specialist work.
Finishing outdoors: impregnating
Outdoors, an impregnating agent protects the slips and the joints against damp, frost, algae and efflorescence. It lets the stone breathe but beads water off.
Apply the impregnating agent only when everything is fully cured (5 to 7 days), on a dry facade. Work from top to bottom, wet on wet, with a low-pressure sprayer or a wide brush.
Choose an agent that does not change the colour if you want to keep the natural look. Reckon on repeating it every 5 to 10 years.
What does installing brick slips cost in 2026?
Prices vary by stone type and whether you do it yourself or have it fitted. Indicative figures for 2026:
| Item | Price per m² (2026) | Notes |
|---|---|---|
| Mineral/concrete slips (material) | 30 to 50 euros | Cheapest, lightest |
| Fired brick slips (material) | 45 to 90 euros | Most authentic look |
| Natural stone slips (material) | 50 to 100 euros | Depends on stone type |
| Adhesive + primer + pointing | 8 to 15 euros | Consumables |
| Corner slips | 6 to 14 euros per linear metre | Only at corners |
| Impregnating (outdoors) | 6 to 10 euros | Material, applied yourself |
| Having it fitted (total, no insulation) | 120 to 200 euros | Including labour and material |
| Having it fitted with external insulation | 180 to 250 euros | Specialist work |
Doing it yourself quickly saves you half. Labour is the biggest part of the bill when fitting.
FAQ about installing brick slips
How long does the adhesive need to dry before I can point?
At least 24 hours. Do not point or load the wall sooner, otherwise the slips shift or the pointing pulls the slips loose. Outdoors and with thicker slips you are better off waiting 48 hours before carrying on.
Can I glue brick slips onto plasterboard?
Yes, indoors that works fine with paste adhesive or flexible adhesive. Do mind the weight though: fired brick weighs 30 to 45 kg per m². Make sure the plasterboard is well screwed down, and when in doubt choose lighter mineral slips. For heavy slips over large areas, a sturdier surface is safer.
Do I really need pointing mortar?
No. You can also install brick slips without joints (jointless, tight against each other). That gives a modern, sleek look and saves a step. Fired brick slips look most authentic with joints, sleek natural stone often just without.
How many brick slips do I need per m²?
Reckon on 40 to 55 slips per m², depending on the format. The exact amount is on the packaging. Always order 10% extra for cutting waste and breakage.
Which adhesive do I use outdoors?
Outdoors, always a cement-based, frost-resistant flexible adhesive (class C2). It absorbs the movement of the facade and survives frost and damp. Paste adhesive is only for indoors and dry rooms, outdoors it lets go within a single winter.
Do I need to impregnate brick slips outdoors?
Yes, that is wise. Impregnating protects the slips and joints against damp, frost and algae. Only do it after full curing (5 to 7 days) on a dry facade, and repeat it every 5 to 10 years.
A wall with brick slips gives your interior or facade instant character, and with the right adhesive and a bit of patience you can do it yourself just fine.
Carrying on with your renovation, or building an extra wall for the slips to go on? Take a look at the clear building plans and step-by-step guides at Fred’s DIY Plans and keep building with confidence.
