You can insulate a wall in three ways: in the cavity (the hollow space between two leaves of brick), on the outside (the facade), or on the inside (a stud wall or insulation boards). If you have no cavity and you are not allowed to change the outside, then internal insulation is what is left. You do that with PIR boards or a stud wall filled with mineral wool, plus a vapour control layer on the warm side. Doing it yourself costs roughly 25 to 60 euros per m² in materials, having it done 130 to 190 euros per m². Insulating an external wall saves around 200 to 300 euros a year according to energy advice bodies. Note: for internal insulation of an external wall, a grant usually requires an Rd value of at least 3.5, and you only qualify if an accredited company carries out the work, not if you do it yourself.
In this article I explain step by step how to tackle it yourself, which mistakes you really must avoid (damp and mould) and what it costs.
The three ways to insulate a wall
Before you start: pick the right method. Internal insulation is not always the best choice, it is often the choice that is left.
| Method | Where | When to choose | Indicative cost/m² (having it done) |
|---|---|---|---|
| Cavity wall insulation | Hollow space between two leaves | House from roughly 1920 onwards with a cavity | 15 to 35 euros |
| External / facade insulation | On the outside, against the facade | No cavity, facade may be changed | 130 to 250 euros |
| Internal wall insulation | On the inside, within the living space | No cavity, facade may not be changed (e.g. listed building, permit) | 130 to 190 euros |
Quick comparison:
Cavity wall is by far the cheapest and least disruptive. A specialist blows beads or flakes into the cavity. If you have a cavity of at least 5 cm, start there. For that, read our separate article on cavity wall insulation.
External insulation (facade) insulates best and solves cold bridges, but it is expensive and you change the look of your house. Often you need a permit. We have a separate article about facade insulation.
Internal insulation is what you can do yourself. It costs space (the wall moves inwards) and you have to get the moisture side right, otherwise you get mould. But it is a fine solution when the other two are not possible. The rest of this article is about this.
What do Rd, Rc and lambda mean?
A quick word on the jargon, because you will run into it everywhere.
Lambda (λ) is the thermal conductivity of the material. Lower is better. PIR sits around 0.022, mineral wool (glass or rock wool) around 0.035. Lower lambda means: at the same thickness you insulate better.
Rd value is the insulation value of the material itself. You work it out as thickness divided by lambda. A PIR board of 80 mm (0.08 m) with lambda 0.022 gives Rd = 0.08 / 0.022 = 3.6. The higher the Rd, the better. For a grant, Rd ≥ 3.5 often applies.
Rc value is the insulation value of the whole construction together (wall plus insulation plus finish). That is a touch higher than the Rd of the insulation alone.
Above all, remember: if you are aiming for a grant or a genuinely warm feeling, you want Rd 3.5 or higher.
How much insulation do you need? Thickness per material
If you want to reach Rd 3.5, the thickness you need depends on the material. This makes a big difference to how much space you lose.
| Material | Lambda (λ) | Thickness for Rd ≈ 3.5 | Thickness for Rd ≈ 4.5 |
|---|---|---|---|
| PIR / phenolic rigid foam | 0.022 | ~80 mm | ~100 mm |
| Glass wool | 0.035 | ~125 mm | ~160 mm |
| Rock wool | 0.035 | ~125 mm | ~160 mm |
| Wood fibre (bio-based) | 0.038 | ~135 mm | ~170 mm |
See the difference? PIR reaches the same insulation value at almost half the thickness. If you have little space, PIR is the logical choice. If you have plenty of space and want it cheaper or more natural, then mineral wool or wood fibre is perfectly fine.
Two ways to insulate an interior wall yourself
There are broadly two routes. Which one you pick depends on how flat your wall is and how much space you are willing to lose.
Option 1: Glue PIR boards or fix them on battens
PIR boards are rigid insulation boards, often already faced with a plasterboard or fibre-gypsum layer so you can wallpaper or paint them straight away.
- Is your wall flat and dry? Then you can glue the boards directly with assembly adhesive or special insulation adhesive.
- Is your wall uneven? Then first screw timber or metal battens to the wall and fix the boards onto those.
Advantage: thin and fast. Disadvantage: uneven walls still call for battens, and PIR is more expensive per m².
Option 2: Stud wall with mineral wool
Here you build a frame (timber battens or metal profiles) against the wall, fill it with glass or rock wool, fit a vapour barrier and screw plasterboard over it.
Advantage: cheaper, you can easily run cables and pipes inside it, and uneven walls are no problem. Disadvantage: thicker, so more lost space, and a bit more work.
My down-to-earth advice: little space and a flat wall? PIR. Plenty of space or a messy wall that needs services running through it? Stud wall with mineral wool.
The single most important thing: the vapour barrier
This is where it goes wrong for DIYers. Read this twice.
Warm indoor air is full of moisture (think showering, cooking, breathing). That warm, moist air wants to move outwards, towards the cold wall. On the way it cools down. At the point where it gets too cold, the moisture settles as condensation. That condensation point is called the dew point.
By insulating your wall on the inside, that dew point shifts inwards, just behind the insulation. If moist air reaches it there, it condenses and you get wet insulation, mould and, in time, rotten battens.
The solution: a vapour barrier on the warm side (the room side), between the insulation and the plasterboard. That barrier holds back moist air so it cannot reach the cold point.
Three iron rules:
- Barrier always on the warm side, so on the room side, not against the wall.
- Fit the barrier airtight. Tape all seams, edges and penetrations (sockets, pipes) with suitable tape. One small hole and it does not work.
- Are you using PIR boards with a vapour-tight aluminium layer on both sides? Then that layer can form the vapour barrier, provided you seal the seams neatly with aluminium tape. Tape every seam.
A cheap tube of sealant or sloppy film here really is false economy. This is what stops mould.
Step-by-step: insulating an interior wall with a stud wall
Allow 2 to 5 days for an average room wall, depending on your pace.
Tools and materials:
- Drill/driver, spirit level, tape measure, pencil
- Insulation knife or saw, sealant gun, staple gun (for the barrier)
- Timber battens (e.g. 44 x 69 mm) or metal profiles
- Mineral wool (glass or rock wool) in the right thickness
- Vapour barrier plus vapour-tight tape
- Plasterboard (12.5 mm) and plasterboard screws
- Sealant/expanding foam or compression tape for the edges
The steps:
-
Mark out the line. Set a line on the floor and ceiling parallel to the wall. Allow for the thickness of insulation + batten + plasterboard. That way you know exactly how much space you are giving up.
-
Check the wall. Damp? Solve the cause first. Never insulate over a wet wall, that just seals the moisture in.
-
Fit the battens. Screw the battens to the wall, usually at 60 cm centres (fits the width of insulation and plasterboard). Seal the joints at floor, ceiling and side walls for airtightness.
-
Fill with insulation. Cut the mineral wool a fraction oversize so it wedges tight between the battens. No gaps, no holes. Gaps = cold bridges.
-
Fit the vapour barrier. Staple the barrier over the whole surface on the room side. Let the runs overlap and tape all seams and edges airtight. Cut a cross at sockets and tape there too.
-
Screw on the plasterboard. Board to board, firmly onto the battens. Leave a few millimetres of space at floor and ceiling.
-
Finish. Fill the joints, sand, then wallpaper or paint.
With PIR boards you skip steps 4 and 5: you glue or screw the boards directly and use the aluminium layer plus tape as the vapour barrier.
Points to watch and pitfalls
Cold bridges. A cold bridge is a spot where the cold still leaks inwards, for example at the junction with the floor, ceiling or a partition wall that has not been insulated along with it. There you get condensation and mould. Insulate a short stretch onto adjoining walls and the ceiling to limit this.
Sockets and switches. They are now in the old wall, but your new wall comes in front of it. You have to move them forward, into the plasterboard. Plan this in advance and make sure every penetration passes through the vapour barrier airtight.
Lost space. A stud wall easily costs 8 to 15 cm per wall. In a small room that adds up. PIR helps here.
Ventilation. A well-insulated and airtight house has to ventilate enough, otherwise moisture lingers inside. Open the vents or consider mechanical ventilation. Insulating without ventilating still gives you mould.
Solve damp first. Penetrating or rising damp in the wall? Tackle it first. Insulation over the top only hides the problem temporarily.
What does it cost to insulate a wall in 2026?
The prices below are indications for materials (doing it yourself) versus a complete job by a company (including labour and finishing, excluding VAT). Source: price indications from insulation suppliers and tradesperson platforms, as of 2026.
| Item | Doing it yourself (material/m²) | Having it done (incl. labour/m²) |
|---|---|---|
| Stud wall with mineral wool | 25 to 45 euros | 130 to 190 euros |
| PIR boards (incl. finish layer) | 40 to 60 euros | 140 to 200 euros |
| Cavity wall (for comparison) | n/a (specialist) | 15 to 35 euros |
For an end-of-terrace house with around 35 m² of external wall, the energy advice figures put it at roughly 1,700 euros if you do it yourself, against about 6,500 euros with a company. The annual saving is estimated at roughly 260 euros. So doing it yourself pays back faster, but then you miss out on the grant (see below).
Grants for wall insulation in 2026
Important and often explained wrongly: for internal insulation of an external wall you can in principle get a grant, because internal insulation of the facade counts as facade insulation. But there are hard conditions attached:
- Minimum Rd value 3.5 for facade insulation (inside or outside of the external wall).
- At least 10 m² of insulation, grant up to a maximum of 170 m².
- An accredited building or installation company must carry out the work. If you do it entirely yourself, you get no grant.
- Grant amount 2026: about 20.25 euros per m² for facade insulation, plus around 6 euros per m² bonus for bio-based material.
- The material has to be on the official approved list. Check this before you buy.
- You apply for the grant within 24 months of the work being done.
Watch out for this pitfall: partition walls and genuine internal walls (walls between two heated rooms) do not qualify. A grant is only available for insulating the outer shell. For comparison: cavity wall insulation has a lower requirement (Rd ≥ 1.1) and a lower amount (around 5.25 euros per m²).
Not sure whether your job qualifies? Use a grant calculator or check the current conditions with your local grant body and energy advice service.
Frequently asked questions
Can I insulate a wall myself or does a company have to do it?
Internal insulation with a stud wall or PIR boards you can do yourself just fine if you are reasonably handy. The only reason to bring in a company is the grant: you only get it when an accredited company carries out the work. Cavity wall insulation you always have a specialist do.
Do I always need a vapour barrier?
For internal insulation of an external wall: yes. Without a vapour control layer on the warm side you will almost certainly get condensation, wet insulation and mould. If you use PIR boards with a vapour-tight aluminium layer and tape all the seams neatly, that layer itself forms the vapour barrier.
How thick should the insulation be?
For good insulation and a grant, aim for Rd 3.5. That is about 80 mm of PIR or 125 mm of mineral wool. If you want it warmer and you have the space, go to 100 mm of PIR (Rd ~4.5) or thicker.
What is the difference between internal wall and cavity wall insulation?
Cavity wall insulation fills the hollow space between two existing leaves, blown in from outside, cheap and with no lost space. With internal wall insulation you build an insulating wall on the inside, more disruptive and with lost space, but possible when there is no cavity.
Will internal wall insulation give me mould?
Only if you do it wrong: a missing or leaky vapour barrier, gaps in the insulation (cold bridges), too little ventilation, or insulating over an already damp wall. If you make the vapour barrier airtight and ventilate well, you actually prevent mould.
How much do I save by insulating a wall?
Insulating the external walls of an average house saves roughly 200 to 300 euros a year according to energy advice bodies, plus a warmer and more comfortable home. The exact saving depends on your current insulation, the surface area and how you heat.
Ready to pulverise your energy bill? Insulating a wall is one of the smartest jobs you will do this year: warmer house, lower bill, paid back faster than you think. Want to know where you save the most and in what order to tackle your house? Then head to Energie Verpulveraar and take the first step. Good luck with the job, Fred.
