You build a slatted garden screen by screwing vertical or horizontal slats (usually 20×45 mm or 28×45 mm) onto a timber frame with posts, at a centre-to-centre spacing of 50 to 80 mm. For a fully private screen, count on a gap of 15 to 25 mm between the slats. If you want more light and air, go to 40 to 60 mm. Budget 60 to 120 euros per linear metre for materials (Douglas fir, 2026), depending on the timber type and slat thickness. In a back garden, a slatted screen up to 2 metres high is usually allowed without planning permission.
In this article you’ll read exactly which timber to choose, which slat sizes and spacings suit your goal, how to build the frame and the foundation, how much timber you need and what it costs. We also explain adjustable louvres with a Flexfence system, so afterwards you won’t need another article.
What exactly is a slatted screen?
A slatted screen is a divider made of narrow timber slats fixed to a frame at a set spacing. You see them as fencing, as the side wall of a canopy, or as a free-standing privacy screen in the garden.
The term louvre screen often gets used interchangeably with slatted screen. The difference: in a louvre screen the slats usually sit at an angle or are adjustable, so you decide for yourself how much people can see in.
A slatted screen combines privacy with an open, clean look. Unlike a solid fence, it lets wind and light partly through, so your garden doesn’t feel like a closed box.
Which timber do you choose for a slatted screen outdoors?
The timber type determines lifespan, price and maintenance. These are the four most commonly used options.
| Timber | Lifespan untreated | Price level | Maintenance | Characteristic |
|---|---|---|---|---|
| Douglas fir | 10-15 years | Medium | Low to medium | Lovely red-brown tone, weathers to silver-grey |
| Larch | 10-15 years | Medium | Low | Resin-rich, repels moisture well |
| Thermowood (heat-treated pine) | 15-25 years | High | Low | Dimensionally stable, shrinks and swells little |
| Pressure-treated pine/spruce | 10-15 years | Low | Medium | Cheapest, green-grey tone |
Douglas fir is the favourite for a slatted screen outdoors. It’s strong, fairly cheap for the quality, and has a warm colour. Left untreated, Douglas fir weathers over a few seasons to a beautiful silver-grey.
Larch is very similar to Douglas fir and, thanks to its high resin content, is naturally well protected against moisture. A solid alternative if the price of Douglas fir is too steep.
Thermowood is pine or ash that has been heat-treated. It absorbs hardly any moisture, so it moves (shrinking and swelling) far less. More expensive, but the nicest end result if you don’t want to re-coat.
Pressure-treated pine or spruce is the budget choice. Pressure-treated timber lasts a long time, but the greenish tone isn’t to everyone’s taste.
Trade term: centre-to-centre spacing means the distance measured from the middle of one slat to the middle of the next slat. That’s easier to work out than the gap in between, because the gap also depends on the slat width.
Which slat sizes and spacings do you use?
The right slat size and gap depend on what you want: maximum privacy, or light and air instead.
Commonly used slat sizes (in mm)
| Slat size (thickness x width) | Use |
|---|---|
| 20 x 45 mm | Light slatted screen, decorative panel |
| 28 x 45 mm | Standard, sturdy and not too heavy |
| 22 x 70 mm | Wider slats, modern look |
| 18 x 145 mm (boards) | Wide board slats, solid wall or adjustable |
For an ordinary slatted screen, 20×45 mm or 28×45 mm works best. Thicker slats (28 mm) warp less and give a sturdier whole.
Centre-to-centre spacing by goal
| Goal | Gap between slats | Centre-to-centre (with 45 mm slat width) |
|---|---|---|
| Maximum privacy | 15-25 mm | 60-70 mm |
| Privacy + air | 30-40 mm | 75-85 mm |
| Open, airy screen | 50-70 mm | 95-115 mm |
Want to make sure nobody can see in at all? Then keep the gap at 15 to 20 mm. The thickness of the slat creates a “privacy angle”: from the side you see nothing, straight on just a thin strip. That’s the whole idea behind a slatted screen: privacy without a solid wall.
Tip: lay a few slats out dry on the ground side by side with different gaps before you start. That way you’ll see straight away which effect suits your garden.
Vertical or horizontal: which is better?
Both work. It’s mainly a question of taste and construction.
Vertical slats let rainwater run off quickly along the slat, so they stay drier and last longer. They make a space look taller. You do need horizontal rails (support beams) in the frame to screw them onto.
Horizontal slats make a garden look wider and give a calm, modern look. The downside: water sits on the top edge of each slat, so wear is slightly higher. In that case go for thermowood or Douglas fir, and make sure the timber can dry out well.
For the longest lifespan with the least worry: vertical Douglas fir slats.
The frame and the foundation: how to make your screen stand firm
A slatted screen is only as strong as its frame. The slats themselves carry nothing. It’s all about the posts and the rails (the horizontal beams between them).
Posts and frame centre-to-centre spacing
- Use posts of 68×68 mm or 70×70 mm for screens up to 2 metres.
- Keep the posts no more than 180 to 200 cm centre-to-centre apart. Further than that and it starts to sag.
- Between the posts you fit horizontal rails (38×58 mm or 45×70 mm) for the vertical slats to sit on, every 40 to 60 cm in height.
Foundation: how do you fix the posts?
You have three options:
- Concrete footings with a post anchor (H-anchor or bolt-down base). The timber doesn’t touch the ground, so the posts won’t rot away. Best choice for a long lifespan. Dig a hole of 40x40x40 cm, pour concrete and set the post anchor into it.
- Posts straight into postcrete. Dig a third of the post length into the ground. For a 200 cm screen that means a post of around 270 cm, with 70 cm going into the ground. Pour postcrete (1 to 2 bags per post) around it.
- Concrete footings loose on the ground for free-standing, movable screens. Only suitable for low, sheltered walls.
On clay soil or a windy, open spot, dig deeper or use heavier footings. Check every post with a spirit level in two directions before the concrete sets.
Important: keep the bottom of the slats at least 5 cm clear of the ground. Timber that touches the ground draws up moisture and rots away first.
Step-by-step: build a slatted garden screen in 8 steps
- Measure and mark out. Decide the length and height. Mark the spot for each post with pegs and a string line for a straight run.
- Dig the foundation holes at no more than 180-200 cm centre-to-centre.
- Set the posts. Place them in post anchors or postcrete, set them plumb with a spirit level and let the concrete cure for 24 hours.
- Fit the horizontal rails between the posts, every 40-60 cm in height. Screw them down with stainless steel screws or timber connectors.
- Decide your centre-to-centre spacing for the slats. Make a spacer jig (a small block of wood at the gap width you want) so every gap comes out the same.
- Screw the first slat on plumb using the spirit level. Use 2 stainless steel screws of 4×40 mm at each crossing with a rail.
- Work slat by slat with the spacer jig in between. Check every few slats that you’re still plumb.
- Finish off. If you like, fit a trim strip on the end grain and treat the timber (see maintenance below).
For Douglas fir and larch we recommend pre-drilling the outermost slats so the timber doesn’t split. With hardwood, always pre-drill with a bit 2 mm thinner than the screw.
Materials list and how much timber do you need?
For a slatted screen of 2 metres high and 4 metres wide with Douglas fir slats of 28×45 mm and a 20 mm gap (privacy):
| Component | Quantity | Size |
|---|---|---|
| Posts | 3 pcs | 70×70 mm, 270 cm |
| Horizontal rails | 12 pcs | 45×70 mm, approx. 190 cm (4 high per bay, 3 bays) |
| Slats | approx. 120 pcs | 28×45 mm, 200 cm |
| Stainless steel screws 4×40 mm | approx. 500 pcs | Stainless A2 |
| Post anchors + bolts | 3 sets | hot-dip galvanised |
| Postcrete | 3-6 bags | 25 kg |
Work out the slats like this: at a slat width of 45 mm + a 20 mm gap, the centre-to-centre spacing is 65 mm. Per metre of width you then need 1000 / 65 = about 15.4 slats, rounded up to 16. For 4 metres wide: 4 x 16 = 64 slats of 200 cm. If you want double-sided or with an overlap, that climbs further.
Always add 5 to 10 percent extra slats for saw waste and warped pieces you set aside.
What does it cost to build a slatted garden screen in 2026?
The cost depends mainly on the timber type and whether you use a ready-made system or loose timber.
| Type | Material cost per linear metre (2 m high, 2026) |
|---|---|
| Pressure-treated pine, loose | 50-75 euros |
| Douglas fir, loose | 60-110 euros |
| Larch, loose | 70-115 euros |
| Thermowood, loose | 110-170 euros |
| Adjustable louvres (Flexfence + boards) | 130-220 euros |
A complete Douglas fir slatted screen of 4 metres wide and 2 metres high costs roughly 250 to 440 euros in materials, excluding tools and treatment. If you have it installed, add around 70 to 110 euros per hour of labour.
Prices vary by timber merchant and by season. Always ask for a quote with the exact slat sizes.
Adjustable louvres and the Flexfence system
Want to be able to choose for yourself how much people can see in? Then adjustable louvres are the answer. With a Flexfence system you build an adjustable louvre screen for the garden, or as the side wall of a canopy.
How does Flexfence work?
Flexfence is a set of rails (stainless steel or black-coated steel) with pivot points. You screw the rails vertically into your posts and clip the boards into the holders. The boards then swing open and shut, just like a blind.
- Suitable boards: 1.6 to 1.8 cm thick and 14 to 14.5 cm wide (for example 16×140 mm pressure-treated pine or Douglas fir).
- A 165 cm rail usually has 14 holders.
- Rails come in lengths from about 50 to 220 cm, so from a low garden wall to a tall fence.
Flexfence costs and fitting (2026)
| Component | Price (2026 guide) |
|---|---|
| Flexfence stainless set 165 cm (2 rails) | 50-70 euros |
| Flexfence stainless set 220 cm (2 rails) | 90-110 euros |
| Board 16x140x1800 mm | 6-9 euros each |
Fitting in brief: mark the centre point of each holder with a pencil, screw the rail into the post with 40 mm stainless screws, and fix each board to the holders with 25 mm stainless screws. With thinner boards use shorter screws (16 mm) so they don’t poke through. With hardwood, pre-drill with a bit 2 mm thinner.
Keep a bay width that matches the rail length. Don’t go wider than the board length you’re using, or the louvres will sag.
How do you maintain a slatted screen outdoors?
Untreated Douglas fir or larch lasts 10 to 15 years and weathers to grey on its own. If you want to keep the natural colour, you treat the timber.
- Stain or wood oil: apply a coat when you build it and repeat every 2 to 4 years, or every 2 years on spots that stand in full sun and rain.
- Penetrating stain (such as a high-quality exterior stain) soaks in deep and protects longer than an ordinary varnish.
- Always use stainless steel screws (A2 or A4). Ordinary screws rust and leave black stains in the timber.
- Keep the bottom clear of the ground and clear leaves and moss from between the slats, so the timber can dry.
Don’t want to do anything? Then choose thermowood, or just let the Douglas fir weather to grey. Silver-grey timber is a deliberate choice, not neglect.
Permission: how high can your slatted screen be?
A slatted screen counts as a boundary fence, so the same rules apply as for fencing. (The figures below are a general guide. Rules vary by country and local authority, so check your own area.)
- Back garden (beside or behind the house): commonly up to 2 metres high without planning permission.
- Front garden (in front of the front façade, adjoining a public area): commonly up to 1 metre high without planning permission.
- On the boundary line you may build, but talk it through with your neighbours first. On your own land you don’t need their consent.
- Local authorities can set extra requirements through the local plan. If in doubt, always check this quickly with your local planning office.
Frequently asked questions about building a slatted garden screen
Which timber is best for a slatted screen outdoors?
Douglas fir is the most commonly chosen timber: strong, affordable and with a lovely colour that weathers to silver-grey. If you want hardly any maintenance and maximum dimensional stability, choose thermowood. Pressure-treated pine is the cheapest option.
How much space do you leave between the slats of a slatted screen?
For maximum privacy you keep a 15 to 25 mm gap between the slats (centre-to-centre about 60-70 mm with 45 mm wide slats). For more light and air you go to a 40 to 60 mm gap.
How deep do the posts of a slatted screen need to go into the ground?
Count on about a third of the post length. For a 200 cm screen you use a post of around 270 cm and set 70 cm into postcrete. With concrete footings and post anchors, the timber doesn’t touch the ground and lasts longer.
What does it cost to build a slatted screen yourself?
In 2026 you’re looking at 60 to 110 euros per linear metre for Douglas fir materials for a 2 metre high screen. A 4 metre wide screen costs roughly 250 to 440 euros in materials, excluding tools and treatment.
Vertical or horizontal: which lasts longer?
Vertical slats last longer because rainwater runs off them faster. On horizontal slats, water sits on the top edge, which speeds up wear a little. With horizontal, go for Douglas fir or thermowood.
Can a slatted screen be 2 metres high without permission?
In a back garden a slatted screen up to 2 metres high is commonly allowed without planning permission, and in a front garden often up to 1 metre. Since local rules vary, check your local plan if in doubt.
Building plans and guides
Want to get going on a slatted screen or canopy without the puzzling? With a solid plan and the right sizes on paper, your screen will stand straight and clean in a single weekend. Take a look at the complete building-plans package at fredsdiyplans.com, with thousands of drawings for every DIY project.
