Here is how you build a desk: take a top of 140 x 70 cm with a thickness of 27 to 40 mm, set it on legs or a frame, and adjust the height to your body. The standard desk height is 74 cm, but the right height for you is your body height divided by 2.4 (so a person of 1.80 m sits at around 75 cm). Reckon on half a day of work and 80 to 250 euros in materials, depending on the wood type and the legs.
In this article I walk you through the whole job step by step. Dimensions, wood, tools, hiding cables, a sit-stand version and the 2026 costs. After this article you won’t need to look anywhere else.
Why build your own desk?
A decent solid wood desk in the shop quickly costs 300 to 600 euros. A wooden top on hairpin legs you can build yourself for less than half that, and you decide the size yourself.
More important still: you fit the desk to your own body. Most ready-made desks are 74 or 75 cm high. Are you 1.70 m, or rather 1.90 m? Then a standard desk sits wrong for you, and you feel it in your neck and shoulders after a working day.
Building it yourself costs you a few hours. The result stands for twenty years.
What is the standard desk height?
The standard desk height is 74 cm (measured from the floor to the top of the surface). That is the European norm most manufacturers stick to.
Those 74 cm work for someone of about 1.78 m. If you are shorter or taller, you want a different height.
Calculating desk height from your body height
Rule of thumb: divide your body height (in cm) by 2.4. That is your ideal desk height with an ordinary office chair.
You’re sitting well when your forearms rest horizontally on the top, your elbows make an angle of about 90 degrees and your shoulders hang relaxed. Your feet are flat on the floor.
Here’s the quick table:
| Body height | Ideal desk height (seated) |
|---|---|
| 1.60 m | 67 cm |
| 1.70 m | 71 cm |
| 1.75 m | 73 cm |
| 1.80 m | 75 cm |
| 1.90 m | 79 cm |
| 2.00 m | 83 cm |
Torn between two sizes? Then go for the higher one and compensate by lowering your office chair. A desk that’s too low is harder to fix than one that’s too high.
When working out your leg length, count in the thickness of the top. If you want a surface height of 75 cm with a 40 mm top, then your legs are 75 – 4 = 71 cm.
What dimensions do you choose for your desk?
The top is the most important choice. Here are the practical dimensions you’ll work to:
| Part | Recommended | Minimum | Generous |
|---|---|---|---|
| Top width | 140 cm | 120 cm | 160-180 cm |
| Top depth | 70 cm | 60 cm | 80 cm |
| Top thickness | 27 mm | 18 mm | 40 mm |
| Legroom (height) | 65 cm clear | 62 cm | – |
| Legroom (width) | 60 cm clear | 50 cm | – |
A few things to keep in mind.
Working with two monitors? Then you want at least 140 cm of width, otherwise everything is crammed together. With just a laptop, 120 cm is plenty.
The 70 cm depth gives you enough distance to your screen (around 50 to 70 cm from your eyes to the picture is healthy) and still leaves room for keyboard and mouse.
A thinner top (18 mm) sags at a width above 120 cm if you don’t support it in the middle. For a wide desk without a centre support, go to 27 mm or thicker, or use a wooden underframe.
Which wood or material do you use?
This is where your desk gets its character. The four most-used options:
| Material | Look | Price guide top 140×70 | Watch out |
|---|---|---|---|
| Scaffold board | Rugged, rustic | 50-90 euros | Moves and warps, dry it first |
| Birch plywood | Clean, visible layers | 70-130 euros | Lovely edges, modern |
| Solid oak | Warm, premium | 200-400 euros | Heavy, pricey, lasts for life |
| Lacquered MDF | Even, budget | 30-60 euros | Not moisture-resistant, less strong |
Scaffold board is the favourite for the rugged look. Buy dry (kiln-dried) scaffold board, not fresh wood, otherwise the top shrinks and cracks after a few months indoors. You glue loose boards together into a top.
Plywood (birch) gives a clean, modern look with that typical striped edge. Choose 18 mm for narrow tops, 27 mm or double-glued for wide ones. Ask the DIY store to cut it to size.
Solid oak is the most beautiful and strongest, but also the most expensive and heaviest. An oak top of 140×70 quickly weighs 20 kg. For a glued oak panel you pay a fair bit, but it lasts you a lifetime.
MDF is the budget choice. Fine as an invisible sub-top or for a temporary desk, but it’s sensitive to moisture and holds screws less well than solid wood.
The base: legs or frame?
The top decides the look, the base decides the sturdiness. Three commonly used options:
- Hairpin legs (steel pin legs): clean, modern, easy to screw on. A set of 4 in 71 cm height costs around 40 to 70 euros. Note: hairpins of 71 cm give a height around 75 cm with a thick top.
- Steel U-legs or square frame legs: heavier, more stable, industrial. From 60 euros per set. Recommended for a heavy oak top.
- Wooden frame (pine or oak beams): build it yourself from 44×44 mm or thicker rails and stiles. Cheap and strong, but more work.
For a top up to 140 cm, four legs are enough. If your desk gets wider than 160 cm, add a fifth leg or a crossbeam in the middle to stop it sagging.
Which tools do you need?
You don’t need a workshop. This is the list for a standard desk on legs:
Basics (must have):
– Cordless drill/driver
– Drill bits and screw bits
– Sander (random orbital) plus sandpaper grit 80, 120 and 240
– Tape measure and pencil
– Spirit level
– Brush or paint roller for the finish
Handy (depending on your plan):
– Circular saw or the DIY store’s cutting service (to get your top to size)
– Wood glue and clamps (when gluing up a scaffold board or oak top)
– Hole saw 50 to 60 mm (for a cable grommet)
– Sanding block for the edges and corners
No circular saw? Then just have your board cut to size at the DIY store. That’s more accurate than by hand and often cheap or free with purchase.
Step-by-step: how to build your desk
Reckon on half a day to a full day, plus drying time for the finish.
Step 1 – Set dimensions and cut.
Decide your width, depth and height (use the tables above). Cut the top to size or have it cut. Working with loose boards (scaffold board)? Glue them together with wood glue and clamps, and let them dry for 24 hours.
Step 2 – Sanding.
Sand the whole top. Start with grit 80 for rough spots, then 120, finish with 240 for a smooth surface. Always sand with the grain, never against it. Don’t forget the edges and corners, you want to round them off slightly so they don’t dig into your forearms.
Step 3 – Drill a cable grommet (optional).
Want your cables run neatly through the top? Drill a hole of 50 or 60 mm now at the spot where your monitor goes, usually at the back in a corner. Do this before the finish, so you can sand and lacquer the cut edge at the same time.
Step 4 – Fit legs or frame.
Lay the top upside down on a cloth or cardboard (otherwise it scratches). Mark in the legs: set them 5 to 8 cm from the edge for stability and nice proportions. Mark the screw holes, pre-drill with a thin bit (prevents splitting) and screw the legs on. For a heavy top, use metal corner brackets for extra sturdiness.
Step 5 – Check.
Stand the desk upright. Check with the spirit level that the top sits level. Does it wobble? Adjust the levelling feet on the legs, or put a felt pad under the short leg.
Step 6 – Finishing.
Treat the wood (see below). Let it dry well before you put your things on it.
How do you finish the wood: oil or lacquer?
Untreated wood stains and dries out. You have two main routes:
| Finish | Look | Maintenance | Protection |
|---|---|---|---|
| Oil (hard wax or wood oil) | Matt, natural, feels like wood | Touch up 1-2x a year | Good, soaks into the wood |
| Lacquer (clear or coloured) | Glossy to matt, film layer | Almost maintenance-free | Strong, protects against moisture |
Oil gives that warm, natural look that scaffold board and oak ask for. It soaks into the wood and still feels like wood. Downside: you touch it up once a year. Apply 2 thin coats with a cloth or brush, let it dry in between, and wipe off the excess oil.
Lacquer lays a protective film layer over the wood. Indestructible against coffee stains and sweaty hands, but it feels less natural. Apply 2 to 3 thin coats, sanding lightly between coats with grit 240.
For a desk that’s used daily and has to take coffee stains, hard wax oil is the golden middle ground: a natural look with good protection.
How do you hide the cables neatly?
Nothing ruins a fine handmade desk as quickly as a tangle of cables underneath. Three things that make the difference:
-
Cable grommet in the top. A hole of 50 to 60 mm with a plastic or metal grommet ring (a few euros) guides your cables neatly downwards.
-
Cable tray under the top. Screw a metal or plastic cable tray to the underside of the top. The power strip and loose cables disappear from view inside it. Costs 10 to 20 euros.
-
Fix the power strip. Screw or stick a power strip under the top instead of on the floor. Saves dragging and keeps everything together.
Do this at the end, when you know where your monitor and laptop go.
Can you build a sit-stand desk yourself?
Yes, and it’s easier than you think. You only have to swap the base for an electrically adjustable sit-stand frame. You screw your own wooden top on top of it.
Here’s how it works:
- Buy an electric sit-stand frame (often with 2 motors and memory presets). Price in 2026: 150 to 350 euros, depending on brand and load capacity.
- Check the frame’s maximum top width (usually adjustable up to 120-180 cm) and the maximum weight (50 to 125 kg). A heavy oak top asks for a stronger frame.
- Screw your handmade top onto the frame. Done.
That way you combine the health benefit of alternating between sitting and standing with the look of your own wooden top. Much cheaper than a complete sit-stand from the shop, and better looking too.
A manual (crank) sit-stand frame also exists, from around 100 euros, but in practice you adjust it less often because it takes more effort.
What does it cost to build a desk yourself? (2026)
Below are three realistic budgets. Prices are guide prices for 2026, including VAT, excluding tools.
| Version | Top | Base | Finish + bits | Total |
|---|---|---|---|---|
| Budget (plywood/MDF + hairpin) | 50 euros | 50 euros | 20 euros | ~120 euros |
| Scaffold board on steel legs | 70 euros | 60 euros | 25 euros | ~155 euros |
| Oak on a wooden frame | 250 euros | 70 euros | 30 euros | ~350 euros |
| Handmade top on a sit-stand frame | 70 euros | 250 euros | 25 euros | ~345 euros |
For comparison: a decent solid wood desk from the shop starts at around 350 euros, a ready-made sit-stand quickly climbs to 500 to 800 euros. Building it yourself saves you a fair bit, and you get exactly the size and look you want.
Frequently asked questions about building a desk
How high should my desk be?
The standard is 74 cm, but the right height for you is your body height (in cm) divided by 2.4. Someone of 1.80 m sits ideally at around 75 cm. You’re sitting well when your forearms lie horizontal, your elbows make 90 degrees and your feet are flat on the floor.
How thick should a desk top be?
For a top up to 120 cm wide, 18 mm is enough. For wider tops (140 cm and more) without a centre support, go to 27 mm or thicker, otherwise the top sags in the middle. Solid oak or scaffold board you often choose in 30 to 40 mm for a sturdy, rugged look.
Which wood is best for a desk?
For a rugged look, choose scaffold board (buy dried wood). For clean and modern, birch plywood. For a premium desk that lasts a lifetime, solid oak. MDF is the budget option, but less strong and not moisture-resistant. Which you choose depends on your taste and budget.
How do I make my desk sturdy so it doesn’t wobble?
Set the legs 5 to 8 cm from the edge, pre-drill the screw holes so the wood doesn’t split, and use metal corner brackets for a heavy top. Check with a spirit level. Still wobbling? Adjust the levelling feet or stick a felt pad under the short leg. For tops over 160 cm, add a centre support.
Can I build a scaffold board desk without experience?
Yes. You make a scaffold board top by gluing loose boards together with wood glue and clamps, then sanding and finishing. The only thing to watch: buy dried scaffold board, otherwise the top shrinks and cracks indoors. With a drill, a sander and a bit of patience, it works the first time.
How long does it take to build a desk?
Reckon on half a day to a full day of active work. On top of that comes drying time: 24 hours if you glue up a top, and per coat of oil or lacquer also several hours to a day of drying. So plan a weekend, then you can build it up in coats at a relaxed pace.
Get started on your own desk
Building a desk is one of the most enjoyable first projects. You don’t need a workshop, the result stands for years, and you get exactly the size and look you want.
Don’t fancy doing the sums and fitting yourself? At Fred’s DIY Plans you’ll find ready-made plans with all the dimensions, a cut list and a materials list to go with them. Then all you have to do is saw, screw and enjoy the result. Good luck with your desk.
