Open floor plans were the standard for years. Wall out, everything open, maximum sense of space. But more and more people are noticing the downsides: cooking smells throughout the house, no place to retreat, and a lack of atmosphere and character. The “broken floor plan” trend reverses that. Instead of fully open or fully closed, you create zones with sight lines, level differences and arch constructions. An arch in the wall combines the best of both worlds: openness and definition at the same time. The good news? You can build a decorative arch construction yourself for 150 to 500 euros in materials. Hiring a contractor will quickly cost you 1,500 to 4,000 euros. In this article, you’ll learn step by step how to build an arch in your wall, what materials you need and what to watch out for.
What exactly is an arch construction?
An arch construction is a curved opening in a wall or partition. In interior design, arches are used as an alternative to straight doorways. They add character, depth and an architectural element to your interior.
There are two main types:
Decorative arch (non-load-bearing). You build an arch onto an existing non-load-bearing wall or create a freestanding arch construction with a metal stud frame and plasterboard. This is the version you can safely tackle as a DIYer.
Structural arch in a load-bearing wall. Here you remove part of a load-bearing wall and replace its structural function with a steel or concrete arch construction. This always requires a structural calculation (from around 550 euros) and a professional contractor. Never do this yourself.
Arch shapes compared
| Arch shape | Look | Difficulty level | Suitable for |
|---|---|---|---|
| Semicircular arch (Roman) | Classic, symmetrical | Medium | Wide doorways (80-120 cm) |
| Segmental arch (flat arch) | Modern, subtle | Easy | Narrow to wide doorways |
| Gothic arch (pointed arch) | Dramatic, statement | Difficult | High ceilings, accent |
| Elliptical arch | Elegant, flowing | Difficult | Wide doorways (100-150 cm) |
| Horseshoe arch (Moorish) | Mediterranean, atmospheric | Difficult | Decorative doorways |
For beginners, the segmental arch or semicircular arch is the most achievable.
Why put an arch in your interior?
The arch construction fits perfectly into the broken floor plan trend that’s becoming increasingly popular in 2025 and 2026. But there are more reasons:
Create zones without closing off space. An arch separates the kitchen from the living room or hallway from the living area, while maintaining the sight line.
Add character. An arch instantly adds architectural character to a standard new-build home. It breaks the monotony of straight lines and flat walls.
Increase value. A well-executed arch construction is a selling point. It stands out during viewings and gives a home a unique look.
Maintain light flow. Unlike a solid wall or door, an arch lets light pass from one room to another.
Improve acoustics. A partial partition with an arch dampens sound better than a completely open space.
Costs: DIY vs. hiring a professional
Total cost overview
| Method | Non-load-bearing wall | Load-bearing wall |
|---|---|---|
| DIY (materials) | 150 – 500 euros | Not recommended |
| Contractor (total) | 800 – 2,000 euros | 2,000 – 4,000 euros |
| Structural calculation | Not needed | From 550 euros |
Material costs in detail (DIY, non-load-bearing wall)
| Material | Specification | Price |
|---|---|---|
| Plasterboard (standard 12.5 mm) | 260 x 120 cm, 2-4 sheets | 8 – 14 euros per sheet |
| Flexible plasterboard (6 mm) | For the curved arch itself | 12 – 18 euros per sheet |
| Metal stud C-profile (stud) | 260 cm, 45 mm, 4-6 pieces | 6 – 8 euros each |
| Metal stud U-profile (track) | 250 cm, 45 mm, 2-4 pieces | 5 – 7 euros each |
| Plasterboard screws | Box of 200 | 6 – 10 euros |
| Joint tape (paper or fibreglass) | Roll of 25 m | 5 – 8 euros |
| Joint filler / jointing compound | Bucket 5 kg | 10 – 18 euros |
| Primer for plasterboard | 5 litres | 15 – 25 euros |
| Finishing plaster or skim coat | Bag 25 kg | 15 – 25 euros |
| Sandpaper (grit 120 + 180) | Per sheet or roll | 5 – 10 euros |
| Acrylic caulk for edge joints | Cartridge | 5 – 8 euros |
| Total materials | 100 – 160 euros |
Add tool costs if you don’t already own them.
Tools you’ll need
| Tool | Do you already have it? | Purchase price |
|---|---|---|
| Cordless drill/driver | Usually yes | 50 – 120 euros |
| Jigsaw or multi-tool | Sometimes | 40 – 80 euros |
| Spirit level (120 cm) | Usually yes | 15 – 30 euros |
| Tin snips (for profiles) | Sometimes not | 10 – 20 euros |
| Plastering trowel | Sometimes not | 8 – 15 euros |
| Pencil, tape measure, set square | Usually yes | 10 – 20 euros |
| Spray bottle with water | Usually yes | 2 – 5 euros |
| Bucket and sponges | Usually yes | 5 – 10 euros |
Step by step: building an arch in a non-load-bearing wall
Method 1: Building an arch in an existing straight doorway
This is the most common situation. You have a straight door opening or passageway and want to turn it into an arch.
Step 1: Design and determine dimensions
- Measure the width of the existing doorway (for example 80 cm)
- Measure the height of the doorway
- Determine the arch height: the radius of the arch. For a semicircular arch, the radius is half the width (so 40 cm for an 80 cm doorway)
- Check that after installing the arch you still have enough clearance height (minimum 200 cm)
- Draw the arch on paper or with a drawing program
Tip for drawing a perfect arch: Take a strip of wood or cardboard. Drill a hole at one end (that becomes your centre point) and a hole at the distance of the radius (that’s where your pencil goes). This way you draw a perfect circular arc.
Step 2: Build the frame
- Cut two U-profiles to the width of the doorway
- Attach them horizontally at the top of the doorway, on both sides (above and below the arch area)
- Cut C-profiles to size as vertical supports on both sides
- Make the curved profile: snip the flanges of a U-profile every 3-5 cm so you can bend it into the desired arch shape
- Attach the curved profile between the vertical supports
- Create an identical frame on both sides of the doorway
Step 3: Attach plasterboard (side panels)
- Lay a plasterboard sheet on the floor
- Draw the arch shape onto the plasterboard using your homemade compass
- Cut out the arch shape with a jigsaw
- Attach the cut plasterboard to the frame with plasterboard screws (every 15 cm)
- Repeat for the other side, making sure both sides are identical
Step 4: The curved piece (the underside of the arch)
This is the trickiest part. You need to bend a strip of plasterboard into the arch shape.
Wet method (recommended for beginners):
1. Cut a strip of plasterboard to the width of the wall thickness
2. Score one side with a needle roller (or poke holes with an awl)
3. Dampen the scored side with a sponge (not soaking, nicely moist)
4. Leave for 1 to 2 hours to absorb
5. Carefully bend the strip over a form or directly onto the frame
6. Secure with screws, starting in the middle and working toward the sides
Dry method with cuts:
1. Make cuts on the inside of the strip every 2-3 cm (for a tight curve) or every 4-5 cm (for a gentle curve)
2. Cut through the paper and plaster, but not through the paper on the other side
3. Bend the strip into the desired shape and attach to the frame
Tip: Use a flexible 6 mm plasterboard for the arch. It bends much more easily than standard 12.5 mm boards and is less likely to crack.
Step 5: Finish with joint filler
- Apply joint tape to all seams and transitions
- Spread a layer of joint filler over the tape
- Let dry for 4-6 hours
- Sand lightly with 120 grit
- Apply a second layer of joint filler, slightly wider than the first
- Let dry again and sand with 180 grit
- Repeat a third time if needed for a perfectly smooth result
Step 6: Plaster or paint
- Apply a thin coat of primer to the plasterboard
- Option A: Skim coat the arch and surrounding wall with finishing plaster for a seamless look
- Option B: Paint directly onto the filled plasterboard (2 coats of emulsion)
- Caulk the edges where the arch meets the existing wall with acrylic sealant
- Paint over the caulk for an invisible transition
Method 2: Build a freestanding arch wall as a room divider
Want to place an arch in the middle of an open space, as a division between living room and dining area? Then you build a freestanding arch wall.
The principle is the same as above, but you build the complete metal stud frame yourself:
- Mark the position of the wall on floor and ceiling
- Attach U-profiles to the floor and ceiling (use wall plugs and screws)
- Place C-profiles as vertical studs every 40-60 cm
- Build the arch frame in the same way as Method 1
- Clad both sides with plasterboard
- Finish with joint filler, primer and paint or plaster
Important: A freestanding wall must be firmly anchored to both floor and ceiling. With a floating floor (laminate, vinyl), you’ll first need to remove the floor covering at the wall location and fix to the subfloor.
Tool tips for a clean result
| Tip | Why |
|---|---|
| Always use a new blade in your jigsaw | A blunt blade tears the plasterboard instead of cutting cleanly through it |
| Work with a vacuum next to your saw | Plaster dust is fine and gets everywhere, protect your lungs with a dust mask |
| Always sand with a lamp shining at an angle across the surface | Raking light reveals every imperfection that you’d miss in daylight |
| Use a flexible spatula for the arch | A rigid plastering trowel won’t follow the curve, use a rubber or flexible plastic spatula |
| Measure three times, cut once | With an arch, every millimetre is visible, take your time for accurate measuring |
Arch in a load-bearing wall: what you need to know
If you want to create an arch in a load-bearing wall, different rules apply. This is not a DIY job.
Always have a structural calculation done. A structural engineer determines what steel construction is needed to take over the wall’s load-bearing function. Cost: from around 550 euros.
Always hire a professional contractor. Removing part of a load-bearing wall and installing a steel beam or arch construction requires specialist knowledge. Cost: 2,000 to 4,000 euros total.
You may need a building permit. For major structural changes, a building permit may be required. Check with your local authority.
How to recognise a load-bearing wall? Load-bearing walls usually run perpendicular to the floor joists. They are often thicker (at least 10 cm) than partition walls. If in doubt, have it checked by a contractor or structural engineer.
Finishing options for your arch
The finish determines how professional your arch looks. There are several options:
| Finish | Look | Cost | Difficulty |
|---|---|---|---|
| Smooth plaster + emulsion paint | Sleek, modern | 20 – 50 euros | Medium |
| Textured plaster (spachtelputz) | Textured, rustic | 30 – 60 euros | Medium to difficult |
| Wallpaper (non-woven) | Decorative, accent | 15 – 40 euros | Easy (on flat sections) |
| Venetian plaster | Luxurious, Mediterranean | 40 – 80 euros | Difficult |
| Unfinished (industrial) | Raw, industrial | 5 – 15 euros (primer only) | Easy |
Tip for plastering the arch itself: The curved section is the hardest to plaster. Work with a thin layer and a flexible spatula. Apply two thin coats rather than one thick coat for a smoother result.
How long does the project take?
| Phase | Duration | Note |
|---|---|---|
| Preparation and measuring | 2 – 3 hours | Including shopping |
| Building the frame | 3 – 5 hours | Depending on complexity |
| Attaching plasterboard | 2 – 4 hours | Including bending the curved section |
| Joint filler (3 coats) | 3 days | Each coat needs to dry |
| Sanding and priming | 2 – 3 hours | After the final coat of filler |
| Painting or plastering | 2 – 4 hours | 2 coats of paint or 1-2 coats of plaster |
| Total | 3 – 5 days | Much of which is drying time |
The active working time is roughly 12 to 20 hours. Most of the total duration is spent waiting for joint filler and paint to dry.
Common mistakes
-
Working on a load-bearing wall without a structural calculation. This is the most dangerous mistake. A load-bearing wall holds up the structure above. Remove a section without calculation and you risk cracks, subsidence or worse.
-
Not marking the arch symmetrically. A crooked arch is immediately noticeable. Always measure from the exact centre of the doorway and use a homemade compass for a perfect circular arc.
-
Too few screws in the curved section. The curved plasterboard is under tension. Use a screw every 10-12 cm in the curved section (instead of the usual 15 cm for flat sections).
-
Skipping the joint tape. Without joint tape on the seams, you’re guaranteed to get cracks in your finish. Always apply joint tape to every seam and transition.
-
Rushing the finish. Each coat of joint filler must be completely dry before applying the next. Don’t force it with a heat source, let it dry at room temperature.
-
Not anchoring the arch wall to floor and ceiling. A freestanding arch wall that only sits on the floor will wobble. Always anchor to both floor and ceiling with the right plugs and screws.
Frequently asked questions
How long does it take to build an arch in a wall?
Expect 2 to 3 days for a DIYer with average experience. Day 1 for the frame and plasterboard, Day 2 for finishing with joint filler (multiple coats with drying time), Day 3 for sanding, priming and painting.
Can I build an arch in any wall?
In a non-load-bearing partition wall, you can build an arch without any problems. In a load-bearing wall, you must always have a structural calculation done first and hire a professional contractor. Look at the wall thickness and the direction of the floor joists to determine whether a wall is load-bearing.
Which arch shape suits a modern interior?
A segmental arch (a wide, gentle curve) fits best in a modern or minimalist interior. A semicircular arch gives a more classic or Mediterranean look. Choose the arch shape that matches the style of your home.
How much does it cost to have a contractor build an arch?
For a non-load-bearing wall, a contractor charges on average 800 to 2,000 euros, depending on complexity. For a load-bearing wall including structural calculation and steelwork, expect to pay 2,000 to 4,000 euros.
Can I build an arch with wood instead of plasterboard?
Yes, you can. Plywood or MDF is an alternative to plasterboard. The advantage is that wood is easier to cut into an arch shape. The disadvantage is that wood is more expensive and harder to finish seamlessly. For a painted arch that looks like part of the wall, plasterboard is the best choice.
Does an arch affect property value?
A well-finished arch construction can enhance the look and thus the value of your home. It’s an architectural detail that stands out during viewings. Make sure the finish is professional though, as a poorly executed arch has the opposite effect.
DIY Plans and Guides
Want to get started right away with professional building plans and step-by-step guides? Check out the complete plan package at fredsdiyplans.com – with thousands of plans for every DIY project.
👉 View all DIY plans
