Mineral wool and PIR boards dominate the insulation market, but an increasing number of DIYers are making a conscious choice for biobased insulation. It makes sense: hemp, flax, cork and wood fibre are renewable, store CO₂ and regulate moisture in a way that synthetic materials cannot match. On top of that, government grants and tightening environmental standards in 2026 actively reward this choice.
But which biobased insulation material suits your project? The thermal performance, prices and handling properties vary considerably. And can you really fit it yourself, or is hiring an installer the wiser option?
In this article you compare the four most popular biobased insulation materials on price, performance and moisture sensitivity. You learn step by step how to fit hemp batts and wood fibre boards yourself, what to consider with vapour barriers, and how to apply for grants for biobased materials. Including an honest cost–benefit analysis of DIY versus hiring a professional.
What exactly is biobased insulation?
Biobased insulation is insulation material made predominantly from renewable, plant-based or animal-derived raw materials. Think of hemp fibres, flax shives, cork oak bark and wood fibres from forestry waste streams.
The difference from conventional insulation is not just in the raw material. Biobased materials have a low or even negative environmental impact, because they absorb and lock in CO₂ as they grow. One cubic metre of hemp insulation stores an average of 35 to 40 kg of CO₂. With PIR or EPS, the CO₂ balance is positive: those materials consume energy and resources to produce.
In addition, most biobased insulation materials are vapour-open. They can absorb moisture, buffer it and release it again without the thermal value dropping significantly. That makes them particularly well suited to older properties with solid walls, where a fully vapour-tight solution can actually cause moisture problems.
An important caveat: “biobased” says nothing about the insulation value. You must always check the thermal conductivity (lambda value) and choose the correct thickness for your situation.
The four most popular biobased materials compared
Below is an overview of hemp, flax, cork and wood fibre on the key criteria. All values are guide prices including VAT per m² at 100 mm thickness, unless stated otherwise.
| Property | Hemp | Flax | Cork (expanded) | Wood fibre |
|---|---|---|---|---|
| Lambda value (W/mK) | 0.038–0.040 | 0.036–0.040 | 0.038–0.042 | 0.038–0.043 |
| R-value at 100 mm | 2.5–2.6 | 2.5–2.8 | 2.4–2.6 | 2.3–2.6 |
| Guide price per m² (100 mm) | £16–£22 | £18–£25 | £26–£40 | £13–£19 |
| Moisture buffering capacity | Very good | Good | Excellent | Good |
| Fire class | Euroclass E (with retardant) | Euroclass E (with retardant) | Euroclass E | Euroclass D–E |
| Dimensional stability | Good (batts) | Moderate (can sag) | Very good (boards) | Very good (boards) |
| Suitable for | Walls, roof, floor | Walls, roof | Facade, roof, floor | Roof, walls, sarking |
| DIY friendly? | Yes, easy | Yes, but trickier | Yes, as boards | Yes, as boards |
Notable: Wood fibre is the most affordable, while cork is the most expensive but offers the best moisture buffering. Hemp scores highest as an all-rounder: good thermal performance, easy to fit yourself and a reasonable price.
Hemp insulation: the all-rounder
Hemp insulation is made from the inner fibres of the hemp plant, often blended with a small percentage of polyester binding fibres (10–15%) and a soda-based fire retardant. The material is supplied as flexible batts or rolls.
Properties
- Lambda value of 0.038–0.040 W/mK, comparable to glass wool
- Excellent moisture regulation: can absorb up to 30% of its own weight in moisture without loss of insulation value
- Good sound insulation due to the fibre structure
- Pleasant to work with: no itching, no respiratory irritation
- Lifespan of 50 years or more when correctly installed
Fitting hemp batts yourself: step by step
What you need: hemp batts to size, long knife or insulation knife, tape measure, straightedge, staple gun or spring clips, vapour control layer (Sd value 2–5 m), tape for the vapour control layer.
- Measure the gap between the studs or rafters. Order the batts 10–20 mm wider than the gap. The friction fit holds them in place without extra fixings.
- Cut to size with a long bread knife or a dedicated insulation knife. Hemp cuts easily. Use a straight edge as a guide.
- Push the batts into place between the studs. Start at the top for a roof, at the bottom for a wall. Compress the batt slightly and let it spring back into the space. There must be no gaps.
- Double layer for a higher R-value. For R 5.0 or higher (roof), work with two layers and stagger the joints. Fit the first layer between the rafters, the second layer at right angles on additional counter-battens.
- Apply the vapour control layer on the warm side (inside). Use a vapour control layer with an Sd value of 2–5 metres, not a fully vapour-tight membrane. Biobased insulation needs to breathe. Tape all joints and junctions airtight.
Common mistake: using a fully vapour-tight polyethylene sheet in combination with hemp. That blocks the moisture-regulating properties and can actually cause condensation problems. Always use an intelligent vapour control layer or variable-diffusion membrane.
Wood fibre insulation: rigid, strong and affordable
Wood fibre insulation is pressed from softwood fibres, usually waste from sawmills. Two types exist: flexible batts (similar to hemp) and rigid boards (density 140–250 kg/m³). The rigid boards are particularly popular as sarking or over-rafter insulation.
Why wood fibre is increasingly popular
- Lowest price per m² of all biobased materials
- Rigid boards provide structural support: you can screw tile battens directly into them
- High heat capacity (2,100 J/kgK): keeps summer heat out better than mineral wool or PIR
- Vapour-open: Sd value of just 2–5 m for rigid boards
- Good sound insulation due to high density
Fitting wood fibre boards yourself (sarking/over-rafter)
What you need: wood fibre boards (40–60 mm for sarking, 100–200 mm for primary insulation), circular saw or hand-held circular saw, screws (special wood fibre screws, length = board thickness + 40 mm), vapour control layer, water-resistant membrane or board with integrated top layer.
- Check the substructure. Wood fibre sarking boards are fixed directly to the rafters or onto a flat timber deck. The surface must be flat and dry.
- Start at the eaves. Lay the first row of boards horizontally, tight against the eaves. Use tongue-and-groove boards for a windtight joint.
- Screw the boards down with dedicated insulation screws. Screw spacing: every 200 mm at the edges, every 300 mm in the field. Screws must penetrate at least 40 mm into the timber.
- Work in a stretcher bond pattern. Offset the vertical joints per row by at least 300 mm. This prevents cold bridges.
- Apply a water-resistant layer over the boards if they do not have an integrated top layer. Then fix counter-battens and tile battens.
Note on wood fibre: the boards are heavy (a board of 1200 x 600 x 100 mm weighs roughly 10 kg). Always work on the roof with two people and use roof scaffolding.
Flax and cork: when should you choose these?
Flax insulation
Flax insulation is made from the short fibres left over after processing flax into textiles. The UK and the Low Countries are major flax producers, so transport distances can be minimal.
Strengths: very good lambda value (as low as 0.036), CO₂-neutral with local production, comfortable to work with.
Weaknesses: flexible batts can sag over time in vertical applications if not sufficiently supported. The price is slightly higher than hemp and wood fibre.
Best application: horizontal or sloped applications (roof, floor), or in walls with sufficient support points. Combine with a rigid wood fibre board on the outside for extra stability.
Expanded cork
Cork is harvested from the bark of the cork oak, primarily in Portugal. Expanded cork (ICB) is pressed under high temperature and pressure into rigid boards, without artificial binders. The natural resin in the cork acts as the adhesive.
Strengths: completely natural (no binders), virtually indestructible (lifespan 80+ years), resistant to mould and pests, excellent moisture regulation, pressure-resistant.
Weaknesses: the highest price per m², limited availability, higher lambda value than hemp or flax.
Best application: floor insulation (pressure-resistant), external wall insulation, applications where moisture resistance is critical (bathroom, cellar). Not the best choice if you are selecting purely on R-value per pound spent.
Vapour barriers and moisture management with biobased insulation
With biobased insulation, moisture management is the most important consideration. The materials themselves handle moisture excellently, but only if the overall construction build-up is correct.
The basic rule
Work from inside to outside with decreasing vapour resistance. The inside (warm side) slows vapour transport; the outside allows moisture to escape freely.
Which vapour barrier for which material?
| Situation | Vapour barrier (inside) | Sd value | Outside |
|---|---|---|---|
| Hemp/flax between studs | Variable-diffusion membrane | 0.2–5 m (variable) | Vapour-open breather membrane |
| Wood fibre sarking | Vapour control layer or OSB + tape | 2–5 m | Wood fibre board itself (vapour-open) |
| Cork on external wall | None (masonry acts as vapour check) | n/a | Cork + render/cladding |
| Biobased in cavity wall | Vapour control layer on inside | 2–5 m | Open cavity with ventilation |
Rule of thumb: with biobased insulation, never use a polyethylene sheet with an Sd value above 100 m. Choose a variable-diffusion membrane (such as Pro Clima Intello or Isover Vario) that acts as a vapour check in winter and becomes vapour-permeable in summer. This allows moisture that migrates outward in winter to dry back in summer.
Airtightness is not the same as vapour-tightness
A common misconception: “if it needs to be vapour-open, it does not need to be airtight.” That is wrong. Airtightness is always necessary. Air movement transports many times more moisture than vapour diffusion. Tape all joints, junctions with walls, windows and service penetrations carefully.
Grants for biobased insulation materials
Several government schemes help fund insulation in existing homes, and biobased materials are increasingly eligible.
UK grants and schemes (2026)
Great British Insulation Scheme (GBIS): Targets homes in lower EPC bands. Eligible measures include loft, cavity and solid wall insulation. Biobased products can qualify provided they meet the required performance standards.
ECO4 (Energy Company Obligation): Requires major energy suppliers to fund energy efficiency improvements in fuel-poor and vulnerable households. Insulation is a core measure, and biobased products are eligible if they meet technical specifications.
Home Upgrade Grant (HUG2): For off-gas-grid homes with low EPC ratings. Covers insulation and other measures. Biobased materials qualify.
Boiler Upgrade Scheme (BUS): Primarily for heat pumps, but insulation work carried out alongside can improve the overall economics of the project.
Conditions to check
- The property is typically a pre-existing dwelling (not new-build)
- Minimum insulation performance thresholds apply (varies by scheme and application: loft, wall, floor)
- The product and installer may need to meet specific certification requirements
- Apply through the relevant scheme administrator or your energy supplier
Lower environmental impact as a bonus
The embodied carbon of insulation materials is receiving increasing attention. Biobased materials score well:
| Material | Indicative embodied carbon | Environmental advantage? |
|---|---|---|
| Hemp | Very low | Yes |
| Flax | Very low | Yes |
| Cork | Low | Yes |
| Wood fibre | Very low | Yes |
| PIR | High | No |
| EPS | High | No |
| Mineral wool | Medium | Moderate |
Some schemes and assessments (such as SAP calculations for EPCs) are beginning to factor in embodied carbon, which further favours biobased choices.
DIY and still eligible for grants?
That depends on the scheme. Some grants (particularly ECO4 and GBIS) require professional installation by an accredited installer. Others may accept DIY work provided you meet all technical requirements and can provide evidence (invoices, photographs). Always check the specific scheme rules before starting.
DIY versus hiring a professional: the honest calculation
Below is an indicative cost comparison for insulating a pitched roof (40 m²) with hemp batts (R 5.0, 200 mm thickness in two layers).
| Cost item | DIY | Professional |
|---|---|---|
| Materials (hemp batts) | £880–£1,050 | £880–£1,050 |
| Variable vapour membrane + tape | £105–£160 | £105–£160 |
| Additional counter-battens (second layer) | £70–£130 | £70–£130 |
| Fixings | £26–£44 | £26–£44 |
| Labour | £0 (your own time) | £700–£1,200 |
| Total excl. grants | £1,080–£1,384 | £1,780–£2,584 |
| Applicable grant (indicative) | varies | varies |
| Typical saving by DIY | £700–£1,200 | — |
Saving by doing it yourself: £700 to £1,200 on a 40 m² roof. Allow one to two working days with two people.
When to hire a professional
- If you are unsure about the construction build-up (vapour layer, ventilation, cold bridges)
- For flat roofs or complex roof shapes with many angles and penetrations
- If you have no experience with airtight working
- For cavity wall insulation: this is almost always specialist work (blown-in)
Frequently asked questions
Is biobased insulation as good as mineral wool or PIR?
In terms of insulation value (lambda), biobased materials perform comparably to mineral wool (0.035–0.040 W/mK). PIR has a lower lambda (0.022–0.026) and therefore insulates better per centimetre. But biobased materials offer advantages PIR does not: moisture regulation, summer heat buffering and a far lower environmental impact.
Can biobased insulation develop mould?
Not when correctly installed. The moisture-buffering property actually prevents condensation. Mould occurs when the construction build-up is wrong — for example, due to the wrong vapour barrier or missing ventilation on the outside. This applies to all insulation materials, not just biobased.
How long does biobased insulation last?
Hemp and wood fibre have an expected lifespan of 50 years or more. Expanded cork can last even longer (80+ years). This is comparable to or better than conventional insulation materials.
Which biobased material is easiest to fit yourself?
Hemp batts. They are light, cut easily, do not itch and friction-fit between studs. Rigid wood fibre boards are also straightforward, but heavier to handle. Cork and flax require slightly more experience.
Do all biobased materials qualify for grants?
Only if the specific product meets the performance and certification requirements of the relevant scheme. Not every brand or product type is registered. Always check scheme eligibility before purchasing.
Can I combine biobased and conventional insulation?
Yes. A common combination is wood fibre boards as sarking (outside) with hemp batts between the rafters (inside). Just make sure the vapour management is correct: the outer layer must always be more vapour-open than the inner layer.
Conclusion
Biobased insulation is no longer a compromise. Hemp, wood fibre, flax and cork perform comparably to conventional materials on thermal value, and on top of that offer moisture regulation, summer heat buffering and a significantly lower environmental impact. Government grants make the choice financially attractive.
For the DIYer, hemp batts and wood fibre boards are the most accessible options. Both can be fitted without specialist tools, provided you get the moisture management right. Invest in a variable-diffusion membrane, work airtight, and you have insulation that lasts for decades.
Calculate in advance which material and which thickness you need to achieve the desired R-value. Check whether your chosen product qualifies for any available grants. And if you are unsure about the construction: get a building physics assessment before you start. That investment of a few hundred pounds pays for itself many times over by preventing mistakes.
Check out our DIY plans at fredsdiyplans.com for more home improvement projects.
