A ready-made rabbit enclosure from the pet store easily costs $150 to $300 and is almost always too small. The minimum space recommended by animal welfare organizations and experienced rabbit keepers is about 30 sq ft (3 m2) per rabbit, and most store-bought runs don’t even meet that for a single animal. Building your own rabbit enclosure takes about a day, you build it to the exact size you need, and you’ll save 30 to 50 percent.
In this article you’ll learn which type of run suits your situation, what materials you need, how large the enclosure should be, and how to build it step by step. Complete with a full materials list, cost comparison, and the mistakes you absolutely want to avoid.
Which Type of Rabbit Enclosure Suits Your Garden?
Not every garden and not every rabbit calls for the same type of run. Decide what you want before you head to the hardware store.
Open Run (No Roof)
A frame of wood and wire mesh, without any roof covering. The simplest and cheapest option. Your rabbits are outdoors in fresh air and can eat the grass.
Note: without a roof, your rabbits are not protected against rain, harsh sun, and birds of prey. You’ll need at least a shade cloth or shelter inside the run.
Suitable for: large gardens where the run is placed under trees, as an extension to an existing hutch, summer use.
Covered Run
The same frame, but with a roof made of corrugated panels, roofing felt, or tarp. This protects against rain, sun, and attacks from birds of prey.
Suitable for: most situations, year-round use, gardens without natural shade.
Portable Run
A lightweight run without a floor that you move regularly across the lawn. The grass recovers in the previous spot while the rabbits graze on a new patch.
Suitable for: large lawns, 1-2 rabbits, owners who want to keep the yard looking tidy.
Permanent Run
A sturdy construction that you build once, often with a concrete or paved base. This is the most predator-resistant option.
Suitable for: multiple rabbits, permanent placement, areas with predators.
| Type | Difficulty Level | Cost (approx.) | Predator-Proof? | Portable? |
|---|---|---|---|---|
| Open run | Beginner | $50 – $100 | Limited | Yes |
| Covered run | Beginner-intermediate | $80 – $180 | Good (top) | Possibly |
| Portable run | Beginner | $60 – $120 | Limited | Yes |
| Permanent run | Intermediate-advanced | $150 – $350 | Very good | No |
Dimensions: How Big Should a Rabbit Enclosure Be?
The biggest mistake rabbit owners make is building too small. A rabbit that can’t run, jump, and binky literally gets sick. Muscle and bone problems, obesity, and behavioral disorders are the direct result.
Minimum Dimensions
Animal welfare guidelines are clear: a minimum of about 30 sq ft (3 m2) per rabbit for the run, plus a shelter of at least 5 sq ft (0.5 m2). The height should be at least 24 inches (60 cm) so the rabbit can sit upright.
But “minimum” is not the same as “enough.” Experienced rabbit keepers recommend 40 to 65 sq ft (4 to 6 m2) per rabbit if you want to house them properly.
| Number of Rabbits | Minimum Run (sq ft / m2) | Recommended Run (sq ft / m2) | Example Dimensions (L x W) |
|---|---|---|---|
| 1 rabbit | 30 sq ft / 3 m2 | 40 – 65 sq ft / 4 – 6 m2 | 80 x 60 in (200 x 150 cm) |
| 2 rabbits | 43 sq ft / 4 m2 | 65 – 86 sq ft / 6 – 8 m2 | 120 x 80 in (300 x 200 cm) |
| 3 rabbits | 65 sq ft / 6 m2 | 86 – 108 sq ft / 8 – 10 m2 | 160 x 80 in (400 x 200 cm) |
| 4 rabbits | 86 sq ft / 8 m2 | 108 – 130 sq ft / 10 – 12 m2 | 160 x 120 in (400 x 300 cm) |
Height
A minimum of 24 inches (60 cm), but 32 to 40 inches (80-100 cm) is better. With a covered run, you also want to be able to reach inside comfortably. A run you have to crawl through to clean will become a chore you hate after a month. Consider a sliding hatch or a large opening lid.
Tip: build the run tall enough that you can stand inside in a bent position (at least 48 inches / 120 cm), or make the roof fully hinged. Your future back will thank you.
Materials and Tools
Materials List (for a covered run of 120 x 80 x 40 in / 300 x 200 x 100 cm)
| Material | Quantity | Approx. Price | Notes |
|---|---|---|---|
| Pressure-treated pine 2×2 in (45 x 45 mm) | 12 pieces (8 ft / 240 cm) | $3 – $5 each | Frame and uprights |
| Pressure-treated pine 2×3 in (45 x 70 mm) | 4 pieces (10 ft / 300 cm) | $5 – $7 each | Top rail and bottom rail |
| Welded wire mesh (1/2 x 1/2 in, 16 gauge) | 86 sq ft (8 m2) | $8 – $12 per m2 | Fine enough to stop weasels |
| Hinges (stainless steel) | 4 pieces | $3 – $5 per pair | For door and/or hinged roof |
| Latch or slide bolt | 2 pieces | $4 – $8 each | Predator-proof (no simple hooks) |
| Wood screws (stainless steel, #8 x 2 in) | 1 box (200 pcs) | $8 – $12 | Stainless is essential for outdoor use |
| Corner brackets | 8 pieces | $1 – $2 each | Reinforcing the corners |
| Corrugated roofing panels | 32 sq ft (3 m2) | $5 – $10 per m2 | Only for covered run |
| Landscape fabric (optional) | 65 sq ft (6 m2) | $2 – $3 per m2 | To prevent digging underneath |
Total material cost: approximately $120 to $200, depending on lumber prices and roofing choice.
Which Wire Mesh Should You Use?
This is where many people go wrong. Chicken wire (hexagonal mesh) is not suitable for a rabbit enclosure. It’s too weak: a weasel or fox can bite right through it, and rabbits can get their feet tangled in it.
Use welded wire mesh (also called hardware cloth) with openings no larger than 1/2 x 1/2 inch (12.5 x 12.5 mm) and a wire gauge of at least 19 (1 mm). Against foxes, you need 16 gauge (1.4 mm) or thicker.
| Mesh Type | Opening Size | Wire Gauge | Protects Against | Price/m2 |
|---|---|---|---|---|
| Chicken wire | 1 in (25 mm hex) | 22 gauge (0.7 mm) | Nothing serious | $2 – $4 |
| Welded wire fine | 1/2 x 1/2 in (12.5 mm) | 19 gauge (1.0 mm) | Weasels, rats | $8 – $12 |
| Welded wire heavy | 1/2 x 1/2 in (12.5 mm) | 16 gauge (1.4 mm) | Foxes, weasels | $12 – $18 |
| Welded wire extra heavy | 1 x 1 in (25 mm) | 14 gauge (2.0 mm) | Foxes (not for young rabbits) | $10 – $15 |
Rule of thumb: always choose welded wire mesh of at least 1/2 x 1/2 inch with 19 gauge wire. In areas with foxes, go to 16 gauge. The price difference is a few dollars; the consequence of using the wrong mesh is irreversible.
Tools
- Cordless drill with bits and drill bits
- Handsaw or circular saw
- Spirit level
- Tape measure (at least 10 ft / 3 meters)
- Speed square
- Heavy-duty staple gun (for attaching mesh) or screws with washers
- Tin snips or wire cutters (for cutting mesh)
- Screwdriver
Predator Protection
A rabbit enclosure without predator protection is a buffet for foxes, weasels, raccoons, birds of prey, and feral cats. Even suburban areas can have these predators.
The 5 Weak Points
1. The Bottom
Foxes and weasels dig. If your run sits directly on the grass without any ground protection, a fox can dig underneath in a single night.
Solutions:
– Lay welded wire mesh under the run, at least 12 inches (30 cm) wider than the frame on all sides (bend the edges outward). Cover with grass or soil.
– Dig a trench 12 inches (30 cm) deep around the run and place mesh vertically in the ground.
– Build the run on a concrete or paved surface.
2. The Mesh
Chicken wire is an open invitation. Use welded wire mesh (see table above).
3. The Latches
Raccoons and weasels are surprisingly dexterous. A simple hook or clip latch they’ll open with ease. Use spring-loaded bolts or latches that require two actions to open.
4. The Roof
Without a roof, your rabbits are vulnerable to hawks, owls, and crows. Especially young rabbits. A solid roof solves this, or span welded wire mesh over the top.
5. Gaps and Cracks
A weasel can fit through an opening of just 1 x 1 inch (3 x 3 cm). Check all connection points and seal them. Staple or screw mesh over all openings, using washers so the mesh doesn’t pull free.
Step-by-Step Building Plan
This building plan is for a covered run of 120 x 80 x 40 inches (300 x 200 x 100 cm). Adjust the dimensions to your situation.
Step 1: Prepare the Ground
Choose a flat spot in the garden, preferably partially in the shade. Remove rocks and branches. If you’re building a permanent run, lay down the landscape fabric or ground mesh now. Let the mesh extend 12 inches (30 cm) beyond all sides.
Step 2: Build the Bottom Frame
Cut the following pieces:
– 2 pieces pressure-treated pine 2×3 in (45 x 70 mm), length 10 ft (300 cm) – long rails
– 2 pieces pressure-treated pine 2×3 in (45 x 70 mm), length 80 in (200 cm) – cross rails
Screw the bottom frame together into a rectangle. Check with a speed square that the corners are 90 degrees. Measure the diagonals: if they’re equal, the frame is square.
Tip: always pre-drill with a 1/8 inch (3 mm) bit to prevent the wood from splitting.
Step 3: Install the Uprights
Cut 4 corner uprights from 2×2 in (45 x 45 mm) stock at 40 inches (100 cm) length. Optionally cut 2 extra intermediate uprights for the long sides (at the midpoint). Screw the uprights to the bottom frame using corner brackets and 2 screws per connection.
Check with a spirit level that each upright is plumb.
Step 4: Build the Top Frame
Cut the same dimensions as the bottom frame:
– 2 pieces 10 ft / 300 cm (long rails)
– 2 pieces 80 in / 200 cm (cross rails)
Screw the top frame to the uprights. Use corner brackets again. The frame must be sturdy, as it will carry the roofing.
Step 5: Create the Door Opening
Decide where you want the door. Cut two extra uprights to the width of the door (at least 24 inches / 60 cm, preferably 32 inches / 80 cm so you can reach through easily). Screw them between the bottom and top frame.
Step 6: Attach the Wire Mesh
This is the most time-consuming part. Cut the mesh to size with tin snips, always 2 inches (5 cm) larger than the opening. Fold the edge over and attach the mesh to the inside of the frame with a heavy-duty staple gun or with screws and washers every 4 to 6 inches (10-15 cm).
Important: attach the mesh to the inside, not the outside. This way a predator cannot push the mesh off the frame. Check for sharp protruding wires and bend them over.
Step 7: Hang the Door
Build a door frame from 2×2 in (45 x 45 mm) wood, covered with mesh. Hang the door with two hinges on an upright. Mount the latch on the outside. Make sure there is no gap larger than 3/4 inch (2 cm) when the door is closed.
Step 8: Install the Roofing
Screw roof battens (1×2 in / 18 x 45 mm) onto the top frame as a support structure, spaced 16 inches (40 cm) apart. Lay corrugated roofing panels on top and fasten them with roofing screws. Let the roof overhang 4 inches (10 cm) on all sides so rainwater drips away from the run.
Build a slight slope (2 to 4 inches / 5-10 cm drop over the width) for water drainage. Do this by cutting the uprights on one side slightly shorter.
Step 9: Finish and Inspect
- Check all screw connections: is everything tight?
- Check the mesh: no openings, no sharp points?
- Seal all gaps larger than 3/4 inch (2 cm) with extra mesh.
- Test the door: does the latch close properly?
- Optional: sand the wood lightly and treat it with a pet-safe wood stain. Do not use creosote or carbolineum — these are toxic to rabbits.
Floor and Ground Surface: What Are Your Options?
The ground surface of the run determines your rabbits’ comfort, ease of cleaning, and protection against predators.
| Surface | Pros | Cons | Suitable For |
|---|---|---|---|
| Grass (direct) | Natural, rabbits can graze | Muddy in rain, rabbits dig underneath, grass disappears quickly | Portable run |
| Landscape fabric + mesh | Predator-proof, grass grows through | Grass wears out over time | Permanent run on lawn |
| Concrete pavers | Predator-proof, easy to clean | Hard, cold, not natural | Permanent run, use thick layer of straw |
| Wood chips | Soft, good drainage | Needs regular topping up, less predator-proof | Covered run with mesh underneath |
| Sand + mesh underneath | Good drainage, rabbits can dig | Needs regular replacement | Permanent run |
Best combination: welded wire mesh on the bottom (predator protection), topped with a 2 to 4 inch (5-10 cm) layer of wood chips or a thick layer of straw. This way your rabbits can sit comfortably and the run is protected from below.
Weather Protection: Living Outdoors Year-Round
Rabbits can live outdoors perfectly well, even in winter, provided they have protection from wind, rain, and extreme heat.
Rain and Wind
- A good roof with 4 inches (10 cm) of overhang keeps most rain out.
- Place at least two solid walls (not mesh, but wood or plexiglass) on the side where the wind usually comes from.
- Include a shelter inside the run: an enclosed corner with three solid walls and a roof. At least 16 x 16 x 12 inches (40 x 40 x 30 cm) per rabbit.
Heat (Summer)
Rabbits are more sensitive to heat than to cold. Above 82 deg F (28 deg C), they quickly overheat.
- Provide shade over the entire run (roof, shade cloth, or placement under trees).
- Place frozen water bottles in the run on very hot days.
- Ensure good ventilation: never close off all sides.
Cold (Winter)
- Fill the shelter with extra straw.
- Place windscreens of plexiglass or tarp on the mesh sides.
- Check daily that the drinking water hasn’t frozen.
Cost Comparison: DIY vs. Store-Bought
The big question. Here’s an honest comparison based on a run of about 120 x 80 x 40 inches (300 x 200 x 100 cm), suitable for 2 rabbits.
| Option | Cost | Size | Mesh Quality | Predator-Proof? |
|---|---|---|---|---|
| Budget pet store run | $80 – $130 | 60 x 24 in (150 x 60 cm) — too small | Thin, sometimes chicken wire | Barely |
| Mid-range pet store | $150 – $250 | 80 x 32 in (200 x 80 cm) — too small | Welded, thin | Limited |
| Premium ready-made | $300 – $500 | 80 x 40 in (200 x 100 cm) | Welded, thick | Reasonable |
| DIY (basic) | $80 – $130 | 120 x 80 in (300 x 200 cm) | Welded, 19 gauge | Good |
| DIY (sturdy) | $150 – $220 | 120 x 80 in (300 x 200 cm) | Welded, 16 gauge | Very good |
| Custom built by carpenter | $400 – $800 | Custom | Your choice | Very good |
The conclusion is clear: for the budget of a mid-range store-bought run, you can build one yourself that’s twice as large, uses sturdier mesh, and is better protected against predators. The only investment is your time: expect 6 to 10 hours for a complete covered run.
Tools included? If you don’t already have a cordless drill or circular saw, add $80 to $150 for the first time. You’ll use that equipment on every future project. Or borrow it.
6 Common Mistakes (and How to Avoid Them)
1. Building Too Small
The number one mistake. A 48 x 24 inch (120 x 60 cm) run from the pet store is a cage, not a home. Build at least 30 sq ft (3 m2) per rabbit, preferably more.
2. Using Chicken Wire
Chicken wire is not fox-proof, not weasel-proof, and rabbits can get their feet tangled in it. Use welded wire mesh, always.
3. Forgetting the Floor
No ground protection means a fox or weasel can dig underneath in a single night. Lay mesh under the run or bury a mesh border in the ground.
4. Using Simple Latches
A hook or clip latch won’t stop a raccoon or weasel. Use spring-loaded bolts or latches that require two actions to open.
5. No Shelter Inside the Run
Rabbits need to be able to hide. It’s a basic need. Without a shelter, they live in constant stress. Place at least one shelter per two rabbits.
6. Using Toxic Wood
Rabbits chew on everything. Don’t use wood treated with creosote, carbolineum, or unknown chemicals. Pressure-treated pine (copper-based, ACQ or MCA treated) is safe. Not sure? Leave the wood untreated or use a pet-safe stain.
Frequently Asked Questions About Building a Rabbit Enclosure
How big should a rabbit enclosure be for 2 rabbits?
Animal welfare guidelines recommend at least 43 sq ft (4 m2) of run space for 2 rabbits, plus a shelter of 5 sq ft (0.5 m2) per rabbit. Experienced rabbit keepers recommend 65 to 86 sq ft (6-8 m2). A run of 120 x 80 inches (300 x 200 cm), which is about 65 sq ft (6 m2), is a good size for two rabbits.
What mesh is suitable for a rabbit enclosure?
Use welded wire mesh (also called hardware cloth) with openings no larger than 1/2 x 1/2 inch (12.5 x 12.5 mm) and a wire gauge of at least 19 (1 mm). Against foxes, choose 16 gauge (1.4 mm). Never use chicken wire: it’s too weak and rabbits can get their feet tangled in it.
Can a rabbit enclosure sit on grass?
Yes, but only if you secure the ground against predators. Lay welded wire mesh under the run and let it extend 12 inches (30 cm) on all sides. With a portable run, move it regularly so the grass can recover. Without ground protection, a fox can dig underneath within a single night.
Can rabbits live outside in a run all year round?
Yes, provided the run is well protected against wind, rain, and extreme heat. Include a shelter with three solid walls, extra straw in winter, and sufficient shade in summer. Rabbits tolerate cold better than heat. Above 82 deg F (28 deg C), they must always have shade and ventilation.
How do I make a rabbit enclosure fox-proof?
Four measures: (1) welded wire mesh of at least 16 gauge (1.4 mm), (2) ground protection by placing mesh under the run or burying it 12 inches (30 cm) deep, (3) spring-loaded bolts or latches on all doors, (4) a roof or mesh over the top. Chicken wire, simple hooks, and an open top are the three biggest risks.
How long does it take to build a rabbit enclosure?
Expect 6 to 10 hours for a complete covered run of 120 x 80 inches (300 x 200 cm), including attaching the mesh and installing roofing. A simple open run without a roof can be built in 3 to 4 hours. Most of the work is in cutting the mesh to size and attaching it.
Want to learn more about DIY and home improvement? Check out the building plans and guides at fredsdiyplans.com — more than 10,000 DIYers have gone before you.
