Buying a bookshelf at IKEA might cost you 60 euros, but after two moves the thing is crooked and the shelves are sagging. Building your own bookshelf takes you a weekend and produces a piece that still looks great ten years from now. Plus: you decide the exact dimensions, the type of wood, and the finish.
In this guide, you’ll learn exactly how to tackle this project. From choosing the right type and material to the last coat of paint. With a materials list, step-by-step building plan, cost comparison, and the mistakes you absolutely want to avoid.
What Type of Bookshelf Suits You?
Before buying wood, decide which type of shelf you want to build. This affects the materials needed, the tools, and the difficulty level.
Freestanding Bookshelf
The classic option. A shelf that stands against the wall but isn’t attached to it (except for an anti-tip strap, which is mandatory). Advantage: you can move it and take it with you when you relocate.
Suitable for: rentals, flexible layouts, beginning DIYers.
Built-In Bookshelf
Fits precisely in an alcove, niche, or space under a sloped wall. You build the shelf to fit, so no space is wasted. This is the most popular option for living rooms.
Suitable for: alcoves, chimney breasts, attic rooms, permanent solutions.
Wall-to-Wall Bookshelf
Runs the full width of a wall and often from floor to ceiling. This is the most impressive type, but also the most labor-intensive. Think carefully about transporting the materials: long planks of 3+ meters don’t fit in every car.
Suitable for: large living rooms, offices, home libraries.
| Type | Difficulty | Cost (indicative) | Movable? |
|---|---|---|---|
| Freestanding | Beginner | 80 – 200 euros | Yes |
| Built-in | Medium | 120 – 350 euros | No |
| Wall-to-wall | Advanced | 250 – 600 euros | No |
Planning: Dimensions, Shelves, and Load Capacity
A bookshelf that sags after a few months is a waste of your effort. Take the planning phase seriously: this is where you make the mistakes that can’t be fixed later.
Standard Dimensions
- Height: 180 – 220 cm (floor to ceiling is about 240 – 260 cm, leave at least 5 cm above the shelf)
- Width: 80 – 120 cm per section (wider than 120 cm requires a vertical divider for strength)
- Depth: 25 – 30 cm for standard books, 35 cm if you want to display large books or decorations
- Shelf thickness: minimum 18 mm, preferably 22 – 25 mm for shelves wider than 80 cm
Shelf Spacing
Many people forget this, but it makes a huge difference in usability:
| Type of Book | Height Needed |
|---|---|
| Paperbacks | 20 – 23 cm |
| Standard novels | 25 – 28 cm |
| Large / A4 books | 32 – 35 cm |
| Coffee table books | 35 – 40 cm |
Tip: make the shelves adjustable by drilling a row of holes every 32 mm in the side panels. Use 5 mm shelf pins. This lets you adjust the height later.
Calculating Load Capacity
Books are heavy. A full shelf 80 cm wide easily carries 25 – 30 kg. Count on 50 – 80 kg per linear meter.
The maximum span (width without support) depends on the material and thickness:
| Material | 18 mm thick | 22 mm thick | 25 mm thick |
|---|---|---|---|
| MDF | Max 60 cm | Max 70 cm | Max 80 cm |
| Particleboard | Max 50 cm | Max 60 cm | Max 70 cm |
| Plywood (birch) | Max 70 cm | Max 85 cm | Max 100 cm |
| Solid pine | Max 75 cm | Max 90 cm | Max 110 cm |
| Solid oak | Max 80 cm | Max 100 cm | Max 120 cm |
Want shelves wider than 100 cm? Add a vertical divider or use thicker boards.
Comparing Materials: What to Choose and What Does It Cost?
The material determines how your bookshelf looks, how long it lasts, and how much you’ll spend. Here are the most common options.
MDF (Medium Density Fiberboard)
Smooth surface, easy to paint, no visible grain. MDF does absorb moisture if not properly sealed, and it’s relatively heavy.
- Price: approx. 15 – 25 euros per m² (18 mm)
- Advantage: sleek, modern look after painting
- Disadvantage: not moisture-resistant, heavy, not suitable for unfinished use
- Suitable for: painted shelves in dry rooms
Plywood (Birch or Okoume)
Stronger than MDF, lighter, and the edges have a beautiful layered pattern that you can leave exposed. Birch plywood is popular for visible work.
- Price: approx. 35 – 55 euros per m² (18 mm birch)
- Advantage: strong, beautiful, easy to work with
- Disadvantage: more expensive than MDF, edges need finishing
- Suitable for: shelves with a natural, Scandinavian look
Solid Wood (Pine, Oak, Beech)
The most beautiful result, but also the most expensive and hardest to work with. Solid wood moves (shrinks and expands), so you need to account for that in construction.
- Price: pine approx. 30 – 45 euros per m², oak approx. 60 – 100 euros per m²
- Advantage: timeless, character, enormous load capacity
- Disadvantage: moves with humidity, expensive, requires more craftsmanship
- Suitable for: statement furniture, classic interiors
Reclaimed / Scaffold Wood
Popular in recent years for a rugged, industrial look. Note: genuinely used scaffold wood may have been treated with chemicals. Buy new scaffold-style wood if in doubt.
- Price: approx. 20 – 35 euros per m²
- Advantage: rugged appearance, cheaper than solid oak
- Disadvantage: irregular dimensions, splinters, possibly treated
- Suitable for: industrial or rustic interiors
Material Comparison at a Glance
| Material | Price/m² | Strength | Look | Workability | Best For |
|---|---|---|---|---|---|
| MDF 18mm | 15 – 25 euros | Moderate | Sleek (painted) | Easy | Budget shelf, sleek design |
| Birch plywood 18mm | 35 – 55 euros | Good | Natural | Medium | Modern, Scandinavian shelf |
| Solid pine | 30 – 45 euros | Good | Warm, grain visible | Medium | Classic bookshelf |
| Solid oak | 60 – 100 euros | Excellent | Luxurious | Difficult | Custom, high-end |
| Scaffold wood | 20 – 35 euros | Moderate-good | Rugged | Easy | Industrial look |
Tools and Materials: What Do You Need?
Tools
- Cordless drill with bit set
- Circular saw or track saw (or have the wood cut to size at the hardware store)
- Spirit level (minimum 60 cm)
- Square
- Tape measure (5 m)
- Pencil
- Sander or sanding blocks (120 and 180 grit)
- Clamps (minimum 4)
- Paint roller and brush (if painting)
Fastening Materials
- Wood screws 4 x 40 mm and 4 x 50 mm
- Wood glue (D3 quality)
- Shelf pins 5 mm (if you want adjustable shelves)
- Wall plugs and screws for wall mounting
- Optional: 8 mm dowels + dowel pins for hidden connections
- Optional: soft-close bumpers
Step-by-Step: Building a Bookshelf
This building plan is based on a freestanding bookshelf of 200 cm tall, 80 cm wide, and 28 cm deep with 5 adjustable shelves. You can adjust the dimensions to your situation.
Step 1: Cut All Parts to Size
You need the following parts:
| Part | Quantity | Dimensions (L x W) |
|---|---|---|
| Side panels | 2 | 200 x 28 cm |
| Top panel | 1 | 76.4 x 28 cm |
| Bottom panel | 1 | 76.4 x 28 cm |
| Fixed middle shelf | 1 | 76.4 x 28 cm (halfway, for extra rigidity) |
| Adjustable shelves | 5 | 76 x 27 cm (slightly narrower for clearance) |
| Back panel | 1 | 200 x 80 cm (3 mm hardboard or 6 mm MDF) |
| Plinth | 1 | 76.4 x 8 cm |
The width of 76.4 cm is the interior measurement: 80 cm total minus 2 x 1.8 cm for the side panels.
Tip: have the wood cut to size at the hardware store. Costs a few euros but saves you a lot of frustration. Ask them to cut a test strip to verify the measurement.
Step 2: Drill the Shelf Pin Holes
Make two rows of drill holes in both side panels for the shelf pins:
– 5 cm from the front and back edges
– Starting at 25 cm from the bottom
– A hole every 32 mm (standard grid spacing)
– Drill diameter: 5 mm, drill depth: 12 mm
Use a drill jig or a straight strip as a guide. Mark the drill depth with a piece of tape on the bit.
Important: drill the holes BEFORE you assemble the bookshelf. Drilling in an assembled shelf is a recipe for crooked holes.
Step 3: Assemble the Base Frame
- Lay a side panel flat on the floor (protect the floor with cardboard)
- Apply wood glue to the end grain of the bottom panel
- Screw the bottom panel to the side panel with 4 x 50 mm screws, pre-drill with 3 mm to prevent splitting
- Repeat for the fixed middle shelf (halfway) and the top panel
- Place the second side panel and screw it in
- Check with a square that everything is at right angles BEFORE the glue dries
Step 4: Attach the Back Panel
The back panel gives the bookshelf its rigidity. Without it, your shelf will go out of square over time.
- Check that the bookshelf is square (measure the diagonals: both must be equal)
- Place the back panel on the rear
- Fasten with small nails or screws every 15 cm along all edges and on the fixed middle shelf
Step 5: Mount the Plinth
Attach the plinth to the bottom of the front. This gives the shelf a finished look and prevents dust from collecting underneath. A 2 cm setback looks nice and makes it easier to stand close to the shelf.
Step 6: Sand and Prepare for Finishing
Sand all visible surfaces:
1. Start with 120 grit to remove irregularities
2. Continue with 180 grit for a smooth finish
3. Remove all sanding dust with a damp cloth
4. Slightly round the sharp edges (2-3 passes over the edge with 180 grit)
Step 7: Finish and Place
See the section below on finishing options. After finishing: let the shelf dry for at least 24 hours, insert the shelf pins in the desired holes, and place the shelves.
Finishing: Paint, Lacquer, or Stain?
The finish determines how your bookshelf looks and how well the wood is protected.
Painting
Gives a sleek, even look. Ideal for MDF and pine. Use an opaque furniture paint on a water base.
- Preparation: apply primer (essential on MDF, which absorbs paint like a sponge)
- Number of coats: 1x primer + 2x topcoat
- Drying time: 4 – 6 hours per coat, light sanding between coats (220 grit)
- Cost: approx. 30 – 50 euros for primer + topcoat
Lacquering
Preserves the natural color and structure of the wood. Use a clear matte or satin lacquer for a modern result.
- Preparation: wood must be dust-free and clean
- Number of coats: 2 – 3 coats, light sanding between coats
- Cost: approx. 20 – 35 euros
Staining
Adds color to the wood while keeping the grain visible. Always combine with a sealing lacquer coat, otherwise the wood is unprotected.
- Preparation: wood must be untreated and clean
- Number of coats: 1 – 2 coats of stain + 1 – 2 coats of lacquer
- Cost: approx. 25 – 45 euros for stain + lacquer
Oiling
Popular for oak and walnut. Gives a warm, matte look and a natural feel. Does need to be refreshed every year.
- Preparation: sand to 180 grit, make dust-free
- Number of coats: 2 – 3 coats, 12 hours drying time per coat
- Cost: approx. 20 – 30 euros
Wall Mounting and Safety
This is not an optional step. A 200 cm tall bookshelf filled with books easily weighs 80 – 150 kg. If it falls on a child or pet, the consequences are devastating.
How to Attach the Bookshelf to the Wall
- Drill two holes in the top of the back of the bookshelf (or use an L-bracket at the top)
- Mark the position on the wall
- Drill into the wall with the correct type of anchor:
– Concrete/masonry: 8 mm masonry bit + nylon plug
– Drywall: special drywall anchors (e.g., toggle bolts) or find the stud behind it
– Wood wall: screw directly into the studs - Fasten the bookshelf with 5 x 60 mm screws
Always test: pull firmly on the top of the bookshelf after mounting. Does it feel solid? Good. Does it wobble? Re-mount with longer plugs or in a different spot.
Cost Comparison: DIY vs Buying
The big question. Here’s an honest comparison based on a bookshelf of approximately 200 x 80 x 28 cm.
| Option | Cost | Quality | Lifespan | Custom? |
|---|---|---|---|---|
| IKEA Billy (80 cm) | 50 – 70 euros | Basic (particleboard) | 3 – 8 years | No (standard sizes) |
| DIY (MDF) | 80 – 130 euros | Good | 10 – 20 years | Yes |
| DIY (plywood) | 140 – 220 euros | Very good | 20+ years | Yes |
| DIY (solid pine) | 120 – 180 euros | Good to very good | 20+ years | Yes |
| DIY (solid oak) | 250 – 400 euros | Excellent | 30+ years | Yes |
| Furniture maker custom | 600 – 1,500 euros | Excellent | 30+ years | Yes |
| Carpenter (built-in) | 800 – 2,500 euros | Excellent | 30+ years | Yes |
Building your own bookshelf from plywood or pine costs about half to a third of a custom-made one. And significantly more than an IKEA Billy, but you get a shelf that fits exactly, doesn’t sag, and lasts for decades.
The honest truth about tools: if you don’t have tools yet, your first project will cost more because you need to buy a cordless drill (from 60 euros) and possibly a circular saw (from 80 euros). You’ll use that equipment for every project after. Or borrow it from a neighbor.
7 Common Mistakes (and How to Avoid Them)
1. Not Using a Back Panel
“Saves money.” No. Without a back panel, your bookshelf will turn into a parallelogram within a few months. That 3 mm hardboard panel costing 5 euros keeps everything square and rigid.
2. Shelves Too Thin for Too Wide a Span
An 18 mm MDF shelf spanning 100 cm will sag as soon as you put books on it. Refer back to the load capacity table and stick to it.
3. Not Pre-Drilling
Driving screws directly into MDF or plywood without pre-drilling? The wood will split, guaranteed. Pre-drill with a 3 mm bit, always.
4. Not Mounting the Bookshelf to the Wall
It’s not a matter of “if” the shelf tips over, but “when.” Especially with children in the house. Two screws into the wall, five minutes of work.
5. Measuring Everything but Checking Nothing
Measure twice, cut once. That saying exists for a reason. Also check whether your wall and floor are level (spoiler: they almost never are). Bring adjustable feet.
6. Using the Wrong Paint or Finish
Regular wall paint on a bookshelf? After a week you’ll have coffee cup rings and fingerprints on it. Use furniture paint or lacquer specifically made for wood.
7. Not Checking Squareness Before the Glue Dries
You have 10 – 15 minutes before wood glue starts to set. Check with a square or by measuring the diagonals. Are they equal? Then it’s square. Not equal? Clamp and correct now, because later it’s too late.
Frequently Asked Questions
How thick should bookshelf shelves be?
For most bookshelves, 18 mm is sufficient, provided the span is no more than 60 – 70 cm (depending on the material). For shelves wider than 80 cm, go to 22 mm or thicker. For heavy books and wide shelves, 25 mm is the safe choice.
What wood is best for a bookshelf?
That depends on your budget and desired look. Birch plywood offers the best combination of price, strength, and appearance. For a budget-friendly shelf you plan to paint, MDF is fine. Want a shelf that lasts a lifetime and looks beautiful? Then solid oak is the best choice.
Can I build a bookshelf without power tools?
Yes, if you have the wood cut to size at the hardware store. You’ll then only need a screwdriver, sandpaper, and a spirit level. It takes more time and muscle, but the result is the same.
How do I prevent shelves from sagging?
Three ways: (1) choose thicker material or a stronger wood species, (2) limit the span (width without support) to maximum 80 cm, (3) add a strip of wood to the front or back of the shelf (a “shelf reinforcer” of 2 x 4 cm that you attach with glue and screws). Option 3 is the cheapest and most effective solution if you want to use thinner material.
How long does it take to build a bookshelf?
Expect 4 – 6 hours of building work for a standard freestanding shelf, excluding drying time for glue and paint/lacquer. With finishing included (painting, lacquering), you’ll spend a full weekend. A built-in or wall-to-wall version can take 2 – 3 days.
Do I have to mount the bookshelf to the wall?
Yes. Always. No exceptions. A filled bookshelf 200 cm tall weighs 80 to 150 kg and has a high center of gravity. It takes five minutes to put two screws in the wall and that can prevent a serious accident.
Want to learn more about DIY and home improvement? Check out the building plans and guides at fredsdiyplans.com — more than 10,000 DIYers have gone before you.
